Air Bearing Basics
What are Air Bearings?
Basically, air bearings use a thin film of pressurized air to support a load, the same way the puck on an air hockey table "floats" on air. This type of bearing is called a "fluid film" bearing. Fluid film bearings have no solid-to-solid contact under typical running conditions; instead, a film of lubricating fluid (in our case pressurized air) forms a layer between the solid machine elements and serves to transfer forces from one to the other. To compare this with ball bearings, in ball bearings the balls are in constant contact with and form a solid bridge between the machine elements.
Approximate Pressure Profile
in an Air Bearing
The fluid is able to transfer forces because as the fluid is pushed through the bearing gap it generates a pressure profile across the bearing area. The force the bearing can support is then:
大内
密探灵灵狗
电影Air Bearing Benefits:▪No solid to solid contact
- No wear, particles or
lubricants
▪Zero static friction
▪Zero running friction
▪High Stiffness
▪Self Centering
▪Error Averaging
Force = Avg. Pressure x Area
The actual pressure distribution in the bearing varies based on the bearing design and other parameters but a good rule of thumb is to expect 30% efficiency.
Force = 0.3 x Supply Pressure x Area
For flat pads and rectangular bearings this calculation is quite straightforward, but for journal and spherical bearings we use a few other approximations to estimate load capacity.
Fluid film bearings offer a number of advantages over mechanical bearings. First, because there is no contact, air bearings do not suffer from wear or heat generation due to friction. They also exhibit no starting or running friction, even under their highest design loading. In addition, the fluid film acts to center and average out small scale errors in the components resulting in motion which can be more accurate than the individual bearing components. Air bearings also offer much higher stiffness
奥密克戎BA.5.2变异株
than rolling element bearings because the air film fully supports the components, as opposed to balls or rollers which have point or line contact and are therefore limited due to Hertzian contact stiffness.
Why Use Air?
While most people are familiar with oil fluid film bearings - for example the crankshaft journal bearings in car engines - most people have not been exposed to air bearings. Remembering our high school physics class, there are two basic types of fluids - liquids and gasses. In terms of fluid film bearings, the difference between these two is essentially the viscosity - liquids have much higher viscosity than gasses. When applied to a fluid film bearing, this difference has a number of implications.
Why we use air (instead of oil):
▪Air is clean, contaminant free
▪Zero friction - no heat
generation at high speeds
▪Small bearing gap means
high accuracy components,
high accuracy motion
▪Air nitrogen of any other
gas can be used
First, lower viscosity means that for the same working pressure gas bearings have lower load capacity (liquid fluid film bearings typically support five times the load of gas bearings for the same pad area). Second, because of the extremely low viscosity of gasses, gas film bearings operate with essentially zero static and running friction where liquid fluid film bearings have much higher friction and pumping losses within the bearings, which can cause heat generation. And third, gas bearings require very tight bearing gaps for proper operation (10 µm for gas compared to up to 100 µm for liquid bearing) which translates into extremely high accuracy requirements on the components.
What this means for air bearings is that although they have a lower load capacity, gas bearings have essentially zero friction at all speeds and because the tight bearing clearances demand high accuracy components this results in extremely high accuracy motion. Another benefit is the cleanliness of using air as a lubricating fluid as opposed to oil, water, or another fluid. Since compressed air is very common in industrial environments it is probably the most often used gas, ho
wever other gasses such as nitrogen can be used where they are available (such as in clean room environments).
Hydrostatic vs. Hydrodynamic?
The first question is how to generate the pressurized supply of fluid for the bearing. There are two ways to do this - one is using an external pressurized supply (hydrostatic) and the other is to use the relative motion of the machine components to generate the pressure internally (hydrodynamic or "self-generating"). While hydrodynamic bearings are common for oil fluid film bearings, which generate internal pressures quite easily due to the relatively high viscosity of oil, it is much rarer to see this technique used for air bearings because the pressure generated is quite low (although Nelson Air has built bearings of this type for low load, high speed rotary applications such as optical scanners).
Hydrodynamic:
Relative Motion
Generates Pressure
Hydrostatic:
External Pressure Supply
Our typical air bearings are hydrostatic (or in our case aerostatic) and use a compressed air supply to create the fluid film. This supply should be clean and regulated to a constant pressure - simple off the shelf air handling components are more than adequate for most applications to clean, dehumidify, and regulate the supply. Typical operating pressures run as low as 20 psi up to 120 psi depending on the stiffness, load capacity, and air consumption requirements.
How does the air get into the bearing?
Porous Carbon Flat Pad
Drilled Nozzles with
Pocketed Compensation
("Setbacks")
孔道Jewel Nozzle with
Pocketed Compensation
After entering the bearing and being routed though internal passages, the next step is to feed the pressurized air to where it is needed - namely directly into the bearing gap. There are two basic ways to accomplish this, orifices and porous media. For orifices, the air flows through a small hole (typically .004" to .015" dia.) into the bearing area. Porous media bearings use a porous material (typically carbon, bronze, or steel) which the air penetrates through into the bearing area.
The relative benefits of each approach are debatable. While orifices typically do not generate as uniform a pressure profile as can be achieved with porous media, there are ways to improve the pressure profile using a technique called "pocketed compensation". Porous media feeding provides more inherent damping than orifices, however proper sizing of the orifices can adjust damping. Orifices can become plugged if a very large particle gets into the air supply (this is extremely rare), where the porous media acts as a filter for the air. However, because of this filtering effect, over time
the porous media itself can become clogged (oil vapor in the air is particularly bad) and a clogged porous bearing is much more difficult to clear than a clogged orifice.
Orifice fed bearings can be made from one piece of material (particularly when using drilled nozzles) where porous bearings are necessarily made using varying materials and adhesives.
At Nelson Air we have used both orifice and porous media feeding. Most of our standard products use pocket compensated orifices, however our LB series of linear bushings use porous bronze. Our typical orifice bearings are made using a special technique we have developed to drill the small orifices directly into the bearing, instead of using pressed in or glued in jewel nozzles. We believe that this technique reduces cost and complexity while increasing long term stability and reliability. However, jeweled nozzles are used when the design precludes drilled nozzles either because of geometry or because especially small orifice sizes (.004" for example) are required.
Geometry, Geometry, Geometry!
Air Film Averages out
Local Variations
Because of the very small gaps that are required for air bearings, the single most important factor in their manufacture is absolutely flawless geometry. Any variation in part size, straightness, squareness or out of roundness will result in a closing of the gap and will cause the bearing to lose its frictionless nature as well as degrade accuracy and load capacity. Typical tolerances on our rectangular bearings which run air gaps of ~0.0005" are part deviations less than ±0.0001" overall. This same tolerance applies over the entire length of the bearing, which for some models can be over 60".
哪种动物会飞?In addition, the part geometry is what determines the accuracy of the final bearing motion - even though local deviations are averaged out by the air film, the overall accuracy is dictated by how well the parts are made. Because of this, Nelson Air has developed a variety of techniques and equipment which allow us to meet these stringent tolerances with repeatability and relatively low cost.
On Accuracy, Precision and Repeatability
Accuracy
Precision
Repeatability
Typical Air Bearing Specs:
▪Linear Accuracy:
10 µin/in, 100 µin/36 in
▪Rotary Accuracy:
±1 µin TIR
▪Roll/Pitch/Yaw:
0.25 arcsec/in
▪Linear Repeatability:
±10 µin
▪Rotary Repeatability:
1 µin
▪Positioning Resolution:
to ±1 encoder count
To start this discussion it is best to briefly define what accuracy, precision and repeatability mean.
赤祼羔羊Accuracy is the measure of how closely the motion follows an ideal profile.
Precision is the measure of how small the motion increments can be.
Repeatability is the measure of how well the motion moves along the same path.
Air bearings offer the best of all worlds because they have excellent accuracy, precision and repeatability. They offer high accuracy because the components are manufactured with extremely tight tolerances and because of the air film's averaging effects. Typical linear accuracies are 10 µin/in with maximum deviation of 100 µin/36 in. Rotary runout can be as low ±1 µin. Air bearings also offer extremely good tilt characteristics - 0.25 arcsec/in.
Because air bearings exhibit no stiction or running friction, the precision achievable is only limited by the abilities of the motor/controller/encoder. Positioning precision of ±1 encoder count can easily be achieved using linear motors.
The repeatability of air bearings far exceeds that of mechanical bearings for the simple reason that they have no contact or wear. Heat generation in mechanical bearings sometimes require "warm up" periods during which there is thermal movement. Also, the mechanical preload on roller bearings can
vary with temperature and cause the bearings to operate differently (varying friction for example) and lack repeatability. When working at the highest accuracy levels, these effects can cause mechanical bearings to lose their accuracy from hour to hour, day to day, or month to month. Because the accuracy of our air bearings is built into its solid metal components (made from one type of material for uniform thermal expansion), they can operate for years without any degradation in accuracy. This way, a calibration done one day will "stick". They also can be run at top speed without any need for warm-up time (excluding motor heating effects) and maintain their best accuracy.
Preloading Air Bearings
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议