编号 | IEC标准编号（含年号） | 对应国家标准编号含年号 | 标准名称（中英文） | 同IEC标准差异（条款差异详细列出） | 备注 | |
1 | IEC 60065 5rd ed.(85) +Amd.1(87)+ Amd.2(92) + Amd.3(93) | GB8898-1997 | 电网电源供电的家用或类似一般用途设备的安全 Safety requirement formains operated electronicand related appartus forhousehold and similar general use | 1) IEC 60065中的4.2.2条：设备的试验电压为额定电压的0.9倍或1.06倍；GB8898根据我国实际情况改为额定电压的0.9倍或1.1倍。在中国境内使用的设备的试验电压应覆盖220V±10%,50Hz. IEC 60065 subclause 4.2.2: Testvoltage is 0.9 times or 1.06 times rated voltage of the equipment; GB8898 subclause 4.2.2: Test voltage is 0.9 times or 1.1 times rated voltage of the equipment, which of the equipment used in China shall cover 220V±10%,50Hz. 2) IEC电源线插头标准为IEC 60083,我国电源线插头标准为GB 1002-1996,为非等同采用IEC60083标准。 IEC standard for plug is IEC 60083; The Chinese national standard for Plugs is GB1002-1996,which is not equivalent with IEC 60083 | ||
2 | IEC 60127-1 1st ed (88) | GB9364.1-97 | 无 | |||
3 | IEC 60127-2 1st ed (89) +Amd. 1(95) | GB9364.2-97 | 管状熔断体Cartidge fuse-links | 无 | ||
4 | IEC 60127-3 2nd ed (88) | GB9364.3-97 | 超小型熔断体 Sub-miniature fuse-links | 无 | ||
5 | 60227-1，2nded (1993) Amd 1(1995) | GB5023.1-1997 | 额定电压450/750V及以下聚氯已烯绝缘电缆 第一部分：一般要求 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750VPart 1:Generalrequirements | 无 | ||
6 | 60227-2, 2nded (1997) | GB5023.2-1997 | 额定电压450/750V及以下聚氯已烯绝缘电缆 第二部分：试验方法 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750VPart 2:Test methods | 无 | ||
7 | 60227-3, 2nded (1993) Amd 1(1997) | GB5023.3-1997 | 额定电压450/750V及以下聚氯已烯绝缘电缆 第三部分：固定布线用无护套电缆 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750VPart 3:Non-sheathed cables for fixed wiring | 无 | ||
8 | 60227-4, 2nded (1992) Amd 1(1997) | GB5023.4-1997 | 额定电压450/750V及以下聚氯已烯绝缘电缆 第四部分：固定布线用护套电缆 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750VPart 4:Sheathed cables for fixed wiring | 无 | ||
9 | 60227-5, 2nded (1997) Amd 1(1997) | GB5023.5-1997 | 额定电压450/750V及以下聚氯已烯绝缘电缆 第五部分：软电缆（电线） Polyvinyl chloride insulated cables of rated voltages up to and including 450/750VPart 5:Flexible cables (cords) | (1) IEC 42平均外径的上下限有所变动 (2) IEC 43导体由第6类改为第5类，增加平均外径下限考核 (3) IEC 52平均外径上下限有所变动 (4) IEC 53平均外径上下限有所变动 (5) 增加IEC 56导体最大温度为90℃的耐热轻型PVC护套软线产品 | ||
10 | 60227-6, 2nded (1985) Amd 1(1997) | GB5023.6-1997 | 额定电压450/750V及以下聚氯已烯绝缘电缆 第六部分：电梯电缆和挠性连接用电缆Polyvinyl chloride insulated cables of rated voltages up to and including 450/750VPart 6:Lift cables and cables for flexible connection | 增加IEC 71 c圆形电梯电缆和挠性连接用电缆产品 | ||
11 | 60227-7, 1sted (1995) | GB5023.7-1997 | 额定电压450/750V及以下聚氯已烯绝缘电缆 第七部分：2芯或多芯屏蔽和非屏蔽软电缆 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750VPart 7:Flexible cables screened and unscreened with two or more conductors | 无 | ||
12 | IEC602385th ed.(1990) Amd1 (1993) Amd2 (1995) | 无 | Edison screw lampholders 螺口灯座 | 无 | ||
13 | IEC60238 6th ed. (1996) Amd1 (1997) Amd2 (1997) | GB17935-1999 | Edison screw lampholders 螺口灯座 | 无 | ||
14 | IEC60238 7th ed. (1998) | 无 | Edison screw lampholders 螺口灯座 | 无 | ||
15 | 60245-1, 3rd ed (1994) Amd 1(1997) Amd 2(1997) | GB5013.1-1997 | 额定电压450/750V及以下橡皮绝缘电缆 第一部分：一般要求 Rubber insulated cables of rated voltages up to and including 450/750VPart 1:General requirements | (1) 3.1.1标志连续性 护套500mm改为550mm, 绝缘200mm改为275mm | ||
16 | 60245-2, 2nd ed (1994) Amd 1(1997) Amd 2(1997) | GB5013.2-1997 | 额定电压450/750V及以下橡皮绝缘电缆 第二部分：试验方法 Rubber insulated cables of rated voltages up to and including 450/750VPart 2:Test methods | (1) 3.1曲挠试验重锤重量、滑轮直径、负载电流有所变动 (2) 增加对要求高柔软场合试验使用的软线IEC86, 87,88产品的滑轮试验、扭绞试验 | ||
17 | 60245-3, 2nd ed (1994) Amd 1(1997) | GB5013.3-1997 | 额定电压450/750V及以下橡皮绝缘电缆 第三部分：耐热硅橡胶绝缘电线 Rubber insulated cables of rated voltages up to and including 450/750VPart 3:Heat resistant silicone insulated cables | 产品由仅考核电线平均外径上限改为考核电线平均外径上限和平均外径下限，同时将原平均外径上限减少0.1～0.5mm， | ||
18 | 60245-4, 2nd ed (1994) Amd 1(1997) | GB5013.4-1997 | 额定电压450/750V及以下橡皮绝缘电缆 第四部分：软线和软电缆 Rubber insulated cables of rated voltages up to and including 450/750VPart 4:Cords and flexible cables | (6) IEC 51, 53, 57, 66平均外径的上下限有所减小 (7) IEC 58, 58f增加平均外径下限考核，原平均外径的上限有所减小 | ||
19 | 60245-5, 2nd ed (1994) | GB5013.5-1997 | 额定电压450/750V及以下橡皮绝缘电缆 第五部分：电梯电缆 Rubber insulated cables of rated voltages up to and including 450/750VPart 5:Lift cables | 无 | ||
20 | 60245-6, 2nd ed (1994) Amd 1(1997) | GB5013.6-1997 | 额定电压450/750V及以下橡皮绝缘电缆 第六部分： 电焊机电缆 Rubber insulated cables of rated voltages up to and including 450/750VPart 6:Arc welding cables | 产品平均外径的上下限有所减小 | ||
21 | 60245-7, 1st ed (1994) Amd 1(1997) | GB5013.7-1997 | 额定电压450/750V及以下橡皮绝缘电缆 第七部分：耐热乙烯－乙酸乙烯酯橡皮绝缘电缆 Rubber insulated cables of rated voltages up to and including 450/750VPart 7:Heat resistant ethylene-vinyl acetate rubber insulated cables | 产品平均外径的上下限有所减小 | ||
22 | 60245-8, 1st ed (1998) | 额定电压450/750V及以下橡皮绝缘电缆 第八部分：要求高柔软场合试验使用的软线 Rubber insulated cables of rated voltages up to and including 450/750VPart 8:Cords for applications requiring high flexibility | 无 | |||
23 | IEC 60252 3rd Ed. (93) | GB3667-97 | 交流电动机电容器 A.C. MotorCapacitors | 无 | ||
24 | 磷脂酰肌醇信号通路IEC60309-2:1989 2nd | GB 11919-89(eqv IEC60309-2:1981+A1:1983) | 工业用插头插座和耦合器 插销和插套尺寸互换性的要求 Plugs, socket-outlets and couplers for industrial purposes Dimensional interchangeability requirements for pin and contact-tube accessories | 1 第1段:用"额定电压交流不超过660V,直流不超过440V,额定频率不超过400Hz"代替"不超过690V、500Hz"；第3段:用"温度为-25~+40℃"代替IEC标准中"一般不超过40℃" 1 1st paragraph: "not exceeding 690V, 500Hz" should be replaced by "not exceeding or and "; 3rd paragraph: "does not normally exceed 40℃" should be replaced by " is -25～+40℃" 4.101 删除 4.101 deleted 5.3 表101删除 5.3 Table 101 should be deleted 7.1 删除 7.1 deleted 8.2 (GB中是3.1) 试验前试样放置时间用24小时代替IEC标准中的4星期 8.2 (GB:3.1) "four weeks" should be replaced by "24h" 9-28 删除 9-28 deleted | ||
25 | IEC60320-1:1994 1st+A1:95+A2:96 | GB17465.1-998(eqv IEC60320-1:1994) | 家用和类似用途的器具耦合器 第一部分:通用要求 Appliance couplers for household and similar general purposes Part1:General requirements | 9- 注3:用"通常不超过35℃,偶尔可达到40℃"代替IEC标准中"通常不超过25℃,偶尔会达到35℃"1 "not normally exceeding 25℃, but occasionally reaching 35℃" should be replaced by "not normally exceeding 35℃, but occasionally reaching 40℃" 9.4用试验环境温度为40℃±2℃代替IEC标准中规定的35℃±2℃ 9.4 "35℃±2℃" should be replaced by "40℃±2℃" 14 用"空气温度应保持在40℃±2℃"代替IEC标准中"20℃~30℃之间任意t值" 14 "any convenient value t℃between 20℃ and 30℃" should be replaced by "40℃±2℃" | ||
26 | IEC60320-2-2:1990 1st+A1:94+A2:97 | GB17465.2-1998(eqv IEC 60320-2-2:1990) | 家用和类似用途的器具耦合器 第二部分:家用和类似设备用互连耦合器 Appliance couplers for household and similar general purposes Part2: Interconnection couplers for household and equipment | 9- 用"通常不超过35℃,偶尔可达到40℃"代替IEC标准中"通常不超过25℃,偶尔会达到35℃" 1 "not normally exceeding 25℃, but occasionally reaching 35℃" should be replaced by "not normally exceeding 35℃, but occasionally reaching 40℃" | ||
27 | IEC60335-1 2nd (1976)A1、A2、A3、A4、A5、A6 | GB4706.1-92 | Safety of Household and similar electrical appliances general requirements 家用和类似电器的安全通用要求 | 1．8 Addition:State of adheres to IEC60335-1In some regions of China which are of subtropics normal ambient temperature exceeds 25℃. 15.4 Addition: For the appliances which are intended to use in subtropical regions ,the relative humidity of the humidity treatment is 90-95%.The temperature of the air at all places where samples can be located is maintained within 40±2℃. 11.8增加采用说明 1） IEC60335-1此处无此注，但前言中有此注。因我国有部分地区为湿热带气候，正常环境温度超过25℃，特在此增加此注。 15．4增加注。对于湿热地区使用的器具，潮湿处理的相对湿度为93（+2或-3）﹪。潮湿室（箱）所有能放置样品处的空气温度均应保持在40±2℃. | ||
28 | IEC60335-2-2 3rd Ed (93) 4th Ed(93) Amd1(97) | GB4706.7-1999 | Safety of household and similar electrical appliances Particular requirements for vacuum cleaners and water suction cleaning appliances 真空吸尘器和吸水式清洁器的特殊要求 | 无 | ||
29 | IEC60335-2-3,3rd (86) Amd1(89) | GB4706.2-96 | Safety of household and similar electrical appliances Particular requirements for electric irons 电熨斗的特殊要求 | 无 | ||
30 | IEC60335-2-4, 4th Ed(93) Amd 1(97) | GB4706.26-2000 | Safety of household and similar electrical appliances Particular requirements for spin extractors 离心式脱水机的特殊要求 | 6．1 Replacement : Appliance shall be of class 0Ⅰ,class Ⅰ,class Ⅱor classⅢ with respect to protection against electric shock. 6.1 替代: 器具就防触电保护方面，应是0Ⅰ类，Ⅰ类，Ⅱ类或Ⅲ类。 | ||
31 | IEC60335-2-53rd Ed(84) | GB4706.25-91 | Safety of household and similar electrical appliances Particular requirements for dishwashers. 洗碟机的特殊要求 | 无 | ||
32 | IEC60335-2-63rd Ed (86) Amd2(incl.Amd 1) (88)and Amd 3 (92) | GB4706.22-88 | Safety of household and similar electrical appliances Particular requirements for cooking ranges, cooking tables, ovens and similar appliances for household use 家用电灶，灶台，烤炉和类似器具的特殊要求 | 无 | ||
33 | IEC60335-2-7, 4th Ed(93) | GB4706.24-2000 | Safety of household and similar electrical appliances Particular requirements for Washing machines. 洗衣机的特殊要求 | 2．2．9 For appliance without heating elements: The temperature of water for appliance in IEC60335-2-7 is 65±5℃,but in GB4706.24-2000 is 50±5℃. 2．2．9 不带电加热元件的器具：所加水的温度在IEC60335-2-7为65±5℃,而GB4706.24-2000为50±5℃。 6．1 Replacement : Appliance shall be of class 0Ⅰ,class Ⅰ,class Ⅱor classⅢ with respect to protection against electric shock. 6.1 替代:器具就防触电保护方面，应是0Ⅰ类，Ⅰ类，Ⅱ类或Ⅲ类。 | ||
34 | IEC60335-2-8, 2nd Ed(81) | GB4706.9-86 | Safety of household and similar electrical appliances Particular requirements for electric shavers, hair clippers and similar appliances 电动剃须刀，电推剪及类似器具的特殊要求 | 无 | ||
35 | IEC60335-2-9, 4th Ed(93) | GB4706.14-1999 | Safety of household and similar electrical appliances Particular requirements for roasters, toasters, waffle irons and similar appliances 电烤箱、面包烘烤器、华夫烙饼模及类似用途器具的特殊要求 | 无 | ||
36 | IEC60335-2-114th Ed (93) | GB4706.20-2000 | Safety of household and similar electrical appliances Particular requirements for tumbler dryers. 滚筒式干衣机的特殊要求 | 无 | ||
37 | IEC60335-2-143rd(84) Amd 1(89) Amd 2(90) | GB4706.30-92 | Safety of household and similar electrical appliances Particular requirements for electrically operated food preparation appliances 电动食品加工机的特殊要求 | 6.2：Water-sealing appliances are not applicable. 无水密型电器。 This sub-clause of IEC 335-1 standard is applicable. IEC 335-1的该条适用 | ||
18.5：This sub-clause of GB4706.1 is not applicable.. GB4706.1的该条不适用。 This sub-clause of IEC 335-1 standard is applicable. IEC 335-1的该条适用。 | ||||||
19.7：This sub-clause of GB4706.1 is not applicable. GB4706.1的该条不适用。 This sub-clause of IEC 335-1 standard is applicable. IEC 335-1的该条适用。 | ||||||
19.8：This sub-clause of GB4706.1 is applicable. GB4706.1的该条适用。 This sub-clause of IEC 335-1 standard is not applicable. IEC 335-1的该条不适用。 | ||||||
20.1：Addition: For the kitchen machines other than hand- hold or using hand to keep switch on, the kitchen machine shall have adequate operation stability. Replacement caused by vibration should not exceed 15mm. Compliance is checked by the following test.Kitchen machines are placed on a horizontal surface of a plain glass plate, drawing the based-angle positional line on the horizontal surface before operating and then the appliance operates under rated load (load which is corresponding to rated input), with the specified working cycle or continual operation way for 1min. After 1min the appliance stop operation, measure the distance of replacement. During test, kitchen machines are not kept stable with hand, except for the machines kept switch on by hand. 该条增加如下内容：除手持式或必须用手保持接通的食品器外，食品器在工作时应有足够的运行稳定性。因震动引起的位移，不应超过15毫米。 通过下述实验确定其是否合格。 将食品器放在水平的玻璃板上，开机前画好底角位置线，食品器加额定负载（规定测量额定输入功率的负载）运行，按规定间歇工作，或连续工作方式总运行时间累计为1min。停机后测量最大位移量。注意，此时不得用手扶住食品器，用手保持通电的食品器除外。 This sub-clause of IEC 335-1 standard is applicable. IEC 335-1的该条适用。 | ||||||
22.25：This sub-clause of GB4706.1 is applicable. GB4706.1的该条适用。 This sub-clause of IEC 335-1 standard is not applicable. IEC335-1标准的该条不适用。 | ||||||
23.7：This sub-clause of GB4706.1 is applicable. GB4706.1的该条适用。 This sub-clause of IEC 335-1 standard is not applicable. IEC335-1标准的该条不适用。 | ||||||
22.28：Kitchen machines filled with liquid shall be so designed that adequate protection against splashing of food or liquid and lid which cause the personal injury should be provided in normal use. 国家标准中新的内容为"装有液体的食品器，设计时应考虑正常使用中防止食物或液体飞溅，危及人身安全的盖子等防护措施。 "It is not concerned in IEC335-1 standard. IEC335-1标准未涉及此内容。 | ||||||
38 | IEC60335-2-15, 4th Ed(95) | GB4706.19-99 | Safety of household and similar electrical appliances Particular requirements for liquid heaters 液体加热器的特殊要求 | 无 | ||
39 | IEC60335-2-16, 3th Ed(94) | GB4706.49-2000 | Food waste disposers 食物垃圾处理机的特殊要求 | 无 | ||
40 | IEC60335-2-19,1st (74) | GB4706.16-86 | Safety of household and similar electrical appliances Particular requirements for battery-powered shavers hair clippers and similar appliances and their charging and battery assemblies 电池驱动的电动剃须刀，电推剪及其充电和电池组的特殊要求 | 无 | ||
41 | IEC60335-2-21, 2nded(89) Amd1(90) Amd2(90) Amd3(92) | GB4706.12-95 | Safety of household and similar electrical appliances Particular requirements for storage water heaters 贮水式电热水器的特殊要求 | clause 19.1: - a capacity exceeding 30L and －a rated input not exceeding 6 kW are replaced by －a ratio of rated input to capacity not exceeding 2kW/10L 19.1条： "－容积超过30L和 －额定输入功率不超过6KW"用"额定输入功率与容器容积之比不大于2KW/10L"代替 | ||
42 | IEC60335-2-23, 3rd Ed(86) Amd (90) | GB4706.15-96 | Safety of household and similar electrical appliances Particular requirements for appliances for skin or hair care 皮肤及毛发护理器具的特殊要求 | 无 | ||
43 | IEC60335-2-24, 3rd Ed(92) | GB4706.13-1998 | Safety of household and similar electrical appliances Particular requirements for refrigerators and food freezers ice-makers 家用电冰箱和食品冷冻箱的特殊要求 | 无 | ||
44 | IEC60335-2-25, 3rd Ed(96) | GB4706.21-96 | Safety of household and similar electrical appliances Particular requirements for microwave ovens 微波炉的特殊要求 | 无 | ||
45 | IEC60335-2-29 2nd Ed(87) | GB4706 .10-93 | Safety of household and similar electrical appliances Particular requirements for massage appliances 按摩电器的特殊要求 | 无 | ||
46 | IEC60335-2-29 3rd Ed(94) | GB4706.18-1999 | Safety of household and similar electrical appliances Particular requirements for battery charges 电池充电器的特殊要求 | 无 | ||
47 | IEC60335-2-30 2rd Ed(90) | GB4706.23-96 | Room Heater室内加热器的特殊要求 | 无 | ||
48 | IEC60335-2-31, 3rd Ed(95) Amd(98) | GB4706.28-99 | Safety of household and similar electrical appliances Particular requirements for cooker or range ventilating hoods 吸油烟机的特殊要求 | 无 | ||
49 | IEC60335-2-32 2nd ed. (87) | GB4706.10-93 | Massage appliances 按摩电器的特殊要求 | 无 | ||
50 | IEC60335-2-341st Ed(80) Amd 1Amd 2(92) Amd 3 (incorp.Amds 1 and 2) | GB4706.17-1996 | Safety of household and similar electrical appliances Particular requirements for motor-compressors 电动机-压缩机的特殊要求 | 无 | ||
51 | IEC60335-2-40,2nded(92) IEC60335-2-40,3rd Ed(95) | GB4706.32-1996 | Safety of household and similar electrical appliances Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers 热泵、空调器和除湿机的特殊要求 | 无 | ||
52 | IEC60335-2-43 2nd Ed(95) | 无（报批稿） | Safety of household and similar electrical appliances Particular requirements for clothes dryers and towel rails 干衣器和毛巾架的特殊要求 | 无 | ||
53 | IEC60335-2-98(97) | GB4707.48-2000 | 加湿器的特殊要求 | 无 | ||
54 | IEC60342-1, 2nd Ed +Amd 1 | GB4706.27-92 | Safety of household and similar electrical appliances Particular requirements for electric fans and regulators 电风扇和调速器的特殊要求 | 11.8 In GB4706.27-92Addition: Electric fans and regulators are based on an ambient temperature not normally exceeding 40℃ in China , the temperature-rise limits in the table are reduced by 15K for compliance criteria. In IEC342-1 it is not concerned. 11．8条：GB4706.27-92中增加了"在国内使用的电风扇和调速器的环境温度以不超过40℃为基准，表中的温升限值应减去15K作为考核依据。 "IEC342-1标准中无此内容。 | ||
55 | IEC 60384-14,2nd ed.(93)+Amd.1(95) | GB/T14472-1998 | 抑制电源电磁干扰用固定电容器 Fixed capacitors for electromagnetic interference suppression and connection to the supply mains | 无 | ||
56 | IEC598-1 3rd ed. (1992) | GB7000.1-1996 | General Safety requirements and tests for lumunaires 灯具一般安全要求与试验 | 无 | ||
57 | IEC60598-1 4th ed. (1996) | 无 | General Safety requirements and tests for lumunaires 灯具一般安全要求与试验 | 无 | ||
58 | IEC60598-1 5th ed. (1999) | 无 | General Safety requirements and tests for lumunaires 灯具一般安全要求与试验 | 无 | ||
59 | IEC60598-2-1 1st ed. (1979) | GB7000.10-99 | Fixed general purpose luminaires 固定式一般用途的灯具 | 无 | ||
60 | IEC60598-2-2 1st ed. (1979) | 无 | Safety requirements for recessed luminaires 嵌入式灯具安全要求 | 无 | ||
61 | IEC60598-2-2 1st ed. (1979) Amd1(87)+Amd2(1991) | 无 | Safety requirements for recessed luminaires 嵌入式灯具安全要求 | 无 | ||
62 | IEC60598-2-2 2.1ed. (1997) | GB7000.12-1999 | Safety requirements for recessed luminaires 嵌入式灯具安全要求 | 无 | ||
63 | IEC60598-2-4 1st ed.(1979) Amd3 (incl. 1+2 1990) | 无 | Safety requirements for portable general purpose luminaires 可移式通用灯具安全要求 | 无 | ||
64 | IEC60598-2-4 2nd ed(1997) | GB7000.11-1999 | Safety requirements for portable general purpose luminaires 可移式通用灯具安全要求 | 无 | ||
65 | IEC60598-2-20 1st ed(1982) Amd1(1987) Amd2(1992) | 无 | Safety requirements for lighting chains 灯串的安全要求 | 无 | ||
66 | IEC60598-2-20 2nd ed.(1996) | GB7000.9-1998 | Safety requirements for lighting chains 灯串的安全要求 | 无 | ||
67 | IEC60669-1:1993 2nd +A1:1994 | GB16915.1-1997 (eqv IEC60669-1:1993) | 家用和类似用途固定式电气装置的开关 第1部分:通用要求Switches for household and similar fixed-electrical installations Part 1 : General requirements | 1 用"通常不超过35℃,偶尔会达到40℃"代替IEC标准中"通常不通过25℃,偶尔会达到35℃ "1 "not normally exceeding 25℃, but occasionally reaching 35℃" should be replaced by "not normally exceeding 35℃, but occasionally reaching 40℃" 6.2增加:"用于小容量的固定式照明用拉线开关的额定电流可以是4A" 6.2 addition: the rated current of cord switch for fixed-electrical installations can be 4A 10.1第5段用"40℃±2℃"代替IEC标准中"35℃±2℃" 10.1 5th paragraph: "35℃±2℃" should be replaced by "40℃±2℃" 15.3用"试验箱的温度应维持在40℃±2℃.将试样放进潮湿箱之前,要使试样达到这个温度"代替IEC标准中"(防潮试验潮湿箱的)温度应维持在20℃~30℃之间的任何方便值t±1K.将试样放进潮湿箱之前,应使试样的温度达到t与t+4K之间". 15.3 "any convenient value t between 20℃ and 30℃" should be replaced by "40℃±2℃" | ||
68 | IEC60669-2-1:1996 3rd+A1:1997 | GB16915.2-2000(eqv IEC 60669-2-1:1996) | 家用和类似用途固定式电气装置开关 第2部分:特殊要求 第1节:电子开关Switches for household and similar fixed-electrical installations Part2:Particular requirements Section1:Electronic switches | 6.2 暂不执行 6.2 not execute in China now13.101 暂不执行 13.101 not execute in China now 17 IEC标准中表102中的绕组部分，改为按绝缘材料等级的允许温升；用表14代替IEC标准本章中的表2 17 temperature rise of windings should be changed according to the degree of insulating material; table 2 should be replaced by table 14 26.1 增加：±10%以内的改变不认为是设定值的改变 26.1 addition: change less than ±10% does not be considered as change of the setting26.1.2 国标试验次数由60次改为10次 26.1.2 60 times should be replaced by 10 times在第 26.1.3条和第26.1.4条的后面增加注"若设定值有改变,应能由控制操作来恢复26.1.3 and 26.1.4 addition: if the setting has changed, reset by the control unit | ||
69 | EC60669-2-2:1996 2nd+A1:97 | GB16915.3-2000(idt IEC 60669-2-2:1996) | 家用和类似用途固定式电气装置的开关 第2部分：特殊要求 第2节：遥控开关（RCS）Switches for household and similar fixed electrical installations- Part2:Particular requirements- Section2:Remote-control switches(RCS) | 8.2 IEC标准中的开关第2和第4种符号没有采用8.2 the 2 & 4th symbols are not adopted | ||
70 | IEC60691 (2nd edition: 93 ) | GB9816-1998 | 热熔断体的要求和应用导则Thermal-links -Requirements and application guide | 无 | ||
71 | IEC60730-1 (2nd edition 93 + amendment 1 94) | GB14536.1-1998 | 《家用和类似用途电自动控制器 第一部分：通用要求》Automatic electrical controls for household and similar use Part 1: General require- ments | 1. IEC60730-1中交直流额定电压均为不超过660V，我国额定电压直流不超过440V，交流不超过660V; In IEC60730-1 the rated voltage is not exceeding 660V both for DC and AC while in GB the DC rated voltage is not exceeding 440V and the AC rated voltage is not exceeding 660; | ||
2．8.4条注1、注2：我国采用。 In GB the sub clauses 8.4 note 1and 2 are adopted。 | ||||||
3．12.1.6条注：对用于防止有害水侵入的密封圈、密封垫及密封剂和将这样的密封垫固定到要安装在雨水环境中及在60℃或以下温度下工作的控制器中的外壳和盖上的胶粘剂应有附加要求。 In our country there are additional requirements for gaskets, glands and sealing compounds employed to prevent harmful ingress of water and to adhesives used for securement of such gaskets to an enclosure or cover in controls to be installed where exposed to rain and operating at or below 60℃. | ||||||
4．12.2.8条增加的注：对于在湿热带地区使用的控制器，潮湿箱内的温度应为40℃±2℃.。 As for the controls which use in tropical zone the temperature of the temperature and humidity chamber should be 40℃±2℃ | ||||||
5．18.4条注：我国采用。 In GB the sub clauses 18.4 note is adopted。 | ||||||
6．19.2.4.1条及19.2.5.1条注：我国采用。 In GB the sub clauses 19.2.4.1and 19.2.5.1note are adopted。 | ||||||
72 | IEC60730-2-1-1989 （1st edition） | GB14536.2-1996 | 《家用和类似用途电自动控制器 家用电器用电控制器的特殊要求》 Automatic electrical controls for household and similar use Particular requirements for electrical controls for electrical household appliance | 无 | ||
73 | IEC60730-2-4-1990 (1st edition ) | GB14536.5-1996 | 《家用和类似用途电自动控制器 密封和半密封电动机-压缩机用电动机热保护器的特殊要求》 Automatic electrical controls for household and similar use Particular requirements for thermal motor protectors for motor compressor of hermetic and semi-hermetic type | 无 | ||
74 | IEC60730-2-6-1991 (1st edition) | GB14536.7-1996 | 《家用和类似用途电自动控制器 压力敏感电自动控制器的特殊要求(包括机械要求) 》 Automatic electrical controls for household and similar use Particular requirements for automatic electrical pressure sensing controls including mechanical requirements | 无 | ||
75 | EC60730-2-7-1990 (1st edition ) | GB14536.8-1996 | 《家用和类似用途电自动控制器 定时器和定时开关的特殊要求》Automatic electrical controls for household and similar use particular requirements for timers and time switches | 1．6.3.6.1条注：我国采用。 In GB the sub clauses 6.3.6.1 note is adopted。 | ||
2．表7.2中注101和注103：我国采用。 In GB the table 7.2 note 101and 103 are adopted。 | ||||||
3．7.2.9条注：我国采用。 In GB the sub clauses 7.2.9 note is adopted | ||||||
4．11.4.104条注：我国采用。 In GB the sub clauses 11.4.104 note is adopted。 | ||||||
5．14.101条注：我国采用。In GB the sub clauses 14.101 note is adopted。 | ||||||
6．17.16.102和17.16.103条注:我国采用。 In GB the sub clauses 17.16.102 and 17.16.103 note are adopted. | ||||||
76 | IEC60730-2-8-1992 (1st edition) | GB14536.9-1996 | 《家用和类似用途电自动控制器 电动水阀的特殊要求（包括机械要求）》Automatic electrical controls for household and similar use Particular requirements for electrically operated water valves, including mechanical requirements | 无 | ||
77 | IEC60730-2-9-1992 (1st edition) | GB14536.10-1996 | 《家用和类似用途电自动控制器 电动机用启动继电器的特殊要求》 Automatic electrical controls for household and similar use Particular requirements for electrically operated motor starting relay | 无 | ||
78 | IEC60730-2-10-1991（1st edition） | GB14536.11-1996 | 《家用和类似用途电自动控制器 电动机用启动继电器的特殊要求》 Automatic electrical controls for household and similar use Particular requirements for electrically operated motor starting relay | 无 | ||
79 | IEC60730-2-11-1993 (1st edition) | GB14536.12-1996 | 《家用和类似用途电自动控制器 能量调节器的特殊要求》 Automatic electrical controls for household and similar use Particular requirements for energy regulators | 无 | ||
80 | IEC60730-2-12-1993 (1st edition) | GB14536.13-1996 | 《家用和类似用途电自动控制器 电动门锁的特殊要求》 Automatic electrical controls for household and similar use Particular requirements for electrically operated door locks | 无 | ||
81 | IEC 60745-1, 1982 | GB3883.1-1991 | 手持式电动工具的安全 第一部分：通用要求 Safety of hand-held motor-operated electric tools Part 1: General requirements | 第23.3条：IEC标准中规定，如果使用插头，该插头应符合IEC83或309出版物中的规定； 我国国家标准中规定，如果使用插头，该插头应符合GB1002－1996中的规定 (即必须使用扁形插脚的插头) | ||
82 | IEC 60745-1, 1997 | GB3883.1-2000 | 手持式电动工具的安全 第一部分：一般要求 Safety of hand-held motor-operated electric tools Part 1: General requirements | 第23.3条：IEC标准中规定，如果使用插头，该插头应符合IEC83或309出版物中的规定； 我国国家标准中规定，如果使用插头，该插头应符合GB1002－1996中的规定 (即必须使用扁形插脚的插头) | ||
83 | IEC 60745-2-1, 1989 Amendment No. 1(1992) | GB3883.6-1991 | 手持式电动工具的安全 第二部分：电钻的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for drills | 第23.3条：IEC标准中规定，如果使用插头，该插头应符合IEC83或309出版物中的规定； 我国国家标准中规定，如果使用插头，该插头应符合GB1002－1996中的规定 (即必须使用扁形插脚的插头) | ||
84 | IEC 60745-2-2, 1982 Amendment No. 1(1991) | GB3883.2-1991 | 手持式电动工具的安全 第二部分：螺丝刀和冲击扳手的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for screwdrivers and impact wrenches | 第23.3条：IEC标准中规定，如果使用插头，该插头应符合IEC83或309出版物中的规定； 我国国家标准中规定，如果使用插头，该插头应符合GB1002－1996中的规定 (即必须使用扁形插脚的插头) | ||
85 | IEC 60745-2-3, 1984 Amendment No. 1(1995) | GB3883.6-1991 | 手持式电动工具的安全 第二部分： 电动砂轮机、抛光机和 盘式砂光机的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for grinders, polishers and disk-type sanders | 第23.3条：IEC标准中规定，如果使用插头，该插头应符合IEC83或309出版物中的规定； 我国国家标准中规定，如果使用插头，该插头应符合GB1002－1996中的规定 (即必须使用扁形插脚的插头) | ||
86 | IEC 60745-2-4, 1983 Amendment No. 1(1992) Amendment No. 2(1995) | GB3883.4-1991 | 手持式电动工具的安全 第二部分： 砂光机的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for sanders | 第23.3条：IEC标准中规定，如果使用插头，该插头应符合IEC83或309出版物中的规定； 我国国家标准中规定，如果使用插头，该插头应符合GB1002－1996中的规定 (即必须使用扁形插脚的插头) | ||
87 | IEC 60745-2-5, 1993 | GB3883.5-1998 | 手持式电动工具的安全 第二部分： 圆锯和圆刀的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for circular saws and circular knives | 第23.3条：IEC标准中规定，如果使用插头，该插头应符合IEC83或309出版物中的规定； 我国国家标准中规定，如果使用插头，该插头应符合GB1002－1996中的规定 (即必须使用扁形插脚的插头) | ||
88 | IEC 60745-2-6, 1989 Amendment No.1(1992) | GB3883.7-1991 | 手持式电动工具的安全 第二部分：电锤的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for hammers | 第2.2.23 条：IEC标准中对旋转电锤的正常负载未作出规定； 电锤产品标准GB7443-1994《电锤》中规定电锤应在额定输入功率条件下连续运行到温度稳定，其余同上 | ||
89 | IEC 60745-2-7, 1989 | GB3883.13-1992 | 手持式电动工具的安全 第二部分：不易燃液体电喷的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for spray guns for non-flammable liquids | 同编号1 | ||
90 | IEC 60745-2-8, 1982 Amendment No.1(1992) | GB3883.8-1991 | 手持式电动工具的安全 第二部分： 电剪刀的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for sheet metal shears | 同编号1 | ||
91 | IEC 60745-2-9, 1984 | GB3883.9-1991 | 手持式电动工具的安全 第二部分： 电动攻丝机的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for tappers | 同编号1 | ||
92 | IEC 60745-2-11, 1984 | GB3883.11-1991 | 手持式电动工具的安全 第二部分： 电动往复锯 (曲线锯、刀锯)的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for reciprocating saws (jig and sabre saws) | 同编号1 | ||
93 | IEC 60745-2-12, 1984 Amendment No.1(1992) | GB3883.12-1991 | 手持式电动工具的安全 第二部分： 混凝土振动器 (插入式振动器)的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for concrete vibrators (internal vibrators) | 同编号1 | ||
94 | IEC 60745-2-13, 1989 Amendment No.1(1992) | GB3883.14-1993 | 手持式电动工具的安全 第二部分： 电链锯的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for chain saws | 同编号1 | ||
95 | IEC 60745-2-14, 1984 | GB3883.10-1991 | 手持式电动工具的安全 第二部分： 电刨的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for planers | 同编号1 | ||
96 | IEC 60745-2-15, 1984 | GB3883.15-1991 | 手持式电动工具的安全 第二部分： 电动修枝剪和电动草剪 的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for planers | 同编号1 | ||
97 | IEC 60745-2-16, 1993 | GB3883.16-1993 | 手持式电动工具的安全 第二部分： 电动钉钉机的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for tackers | 同编号1 | ||
98 | IEC 60745-2-17, 1989 | GB3883.17-1993 | 手持式电动工具的安全 第二部分： 电动木铣和电动修边机的专用要求 Safety of hand-held motor-operated electric tools Part 2: Particular requirements for routers and trimmers | 同编号1 | ||
99 | IEC60884-2-2:1989 1st | GB2099.2-1997(eqv IEC60884-2-2:1989) | 家用和类似用途插头插座 第二部分:器具插座的特殊要求 Plugs and socket-outlets for household and similar purposes Part 2: Particular requirements for socket-outlets for appliances | 9.1 增加：器具插座的型式尺寸应符合GB1002或相关标准的要求 9.1 addition: Types, basic parameters and dimensions of socket-outlets for appliances shall comply with GB1002 or the relational standards. | ||
100 | IEC884-2-5:1995 1st | GB2099.3-1997(idt IEC 884-2-5:1995) | 家用和类似用途插头插座 第二部分:转换器的特殊要求Plugs and socket-outlets for household and similar purposes-Part2: Particular requirements for adaptors | 9.1 增加：转换器的插头部分应符合GB1002的要求 9.1 addition: plugs of adaptor shall comply with GB1002 9.3 增加注：转换器中插座部分应能满足国外和地区相应标准的插头插座的要求。（也允许同时兼容几种型式插座的插孔） 9.3 addition: socket-outlets of adaptor shall comply with the standards in foreign countries and areas. ( hole for several type plugs is admitted) 24.9 国标仅考核带软缆的转换器的插座部分 24.9 socket-outlets of adaptor with cord should be checked only | ||
101 | IEC60920 1st ed. (1990) | GB2313-1993 | Ballasts for tubular fluoresent lamps general and safety requirements 管形荧光灯镇流器一般要求和安全要求 | 无 | ||
102 | IEC60921 1st ed.(1988) | GB/T14044-93 | Ballasts for tubular fluorecent lamps performance requirements 管形荧光灯镇流器性能要求 | Only some types of ballast suitable for operating on 220V 50Hz are included in clause 4.3 of GB/T14044. GB/T14044-1993仅适用于IEC60921中的部分规格镇流器，这是由GB/T14044-93 4.3条所引起，只考虑了工作于220V 50Hz下的一些荧光灯用镇流器。 | ||
103 | 再过五十年IEC60921 1st ed.（1988） Amd1（1990） Amd2（1994） | 无 | Ballasts for tubular fluorecent lamps performance requirements 管形荧光灯镇流器性能要求 | 无 | ||
104 | IEC60928 1st ed.（1990） IEC60928 2nd ed.（1995） Amd1（1999） | GB15143-94无 | A.C. Supplied Electronic Ballast for tubular fluorescent lamps general and safety requirements 管形荧光灯用交流电子镇流器一般要求和安全要求 | 无 | ||
105 | IEC60928 2nd ed.（1995） Amd1（1999） | GB4943-1995 | A.C. Supplied Electronic Ballast for tubular fluorescent lamps general and safety requirements 管形荧光灯用交流电子镇流器一般要求和安全要求 信息技术设备（包括电气事务设备）的安全 | 1) IEC 60950中的1.4.5和1.6.5条电源容差为-10%,+6%； GB4943中根据我国实际情况改为-10%,+10% IEC 60950 sub-clause 1.4.5 and 1.6.5: The minimum supply tolerance is -10%,+6%;GB4943 sub-clause 1.4.5 and 1.65: The minimum supply tolerance is -10%, +10%according to Chinese situation. 2) IEC电源线插头标准为IEC 60083,我国电源线插头标准为GB 1002-1996,为非等同采用IEC60083标准。 IEC standard for plug is IEC 60083; The Chinese National standard for Plugs is GB1002-1996,which is not equivalent with IEC 60083 | ||
106 | IEC 60950 2nd ed. (1991) IEC60967, 1st Ed（88） Amd 1（91） | GB17652-98 | Safety of information technology equipment including electricalbusiness equipment Electrically heated blankets, pads and mattresses 电热毯、电热垫和家用类似柔性发热器具的安全 | 无 | ||
107 | IEC60968 1st ed. （1988）+Amd1（1991） | GB16844-1997 | Self-ballasted lamps for general lighting services safety requirements 普通照明用自镇流灯的安全要求 | 无 | ||
108 | IEC60998-1:1990 1st | GB13140.1-1997(idt IEC60998-1:1990) | 家用和类似用途低压电路用的连接器件 第1部分:通用要求 Connecting devices for low voltage circuits for household and similar purposes Part1:General requirements | 无 | ||
109 | IEC60998-2-1:1990 1st | GB13140.2-1998(idt IEC60998-2-1:1990) | 家用和类似用途低压电路用的连接器件 第2部分:作为独立单元的带螺纹型夹紧件的连接器件的特殊要求Connecting devices for low voltage circuits for household and similar purposesPart2:Particular requirements for connecting devices as separate entities with screw-type clamping units | 无 | ||
110 | IEC60998-2-2:1991 1st IEC60998-2-3:1991 IEC60998-2-4:1993 | GB13140.3-1998(idt IEC 60998-2-2:1991)GB13140.4-1998(idt IEC60998-2-3:1991)GB13140.5-1998(idt IEC60998-2-4:1993) | 家用和类似用途低压电路用的连接器件 第2部分:作为独立单元的带无螺纹型夹紧件的连接器件的特殊要求 Connecting devices for low voltage circuits for household and similar purposes Part 2: Particular requirements for connecting devices as separate entities with screwless-typeClamping units 家用和类似用途低压电路用的连接器件 第2部分:作为独立单元的带刺穿绝缘型夹紧的连接器件的特殊要求 Connecting devices for low voltage circuits for household and similar purposes Part2:Particular requirements for connecting devices as separate entities with insulation piercing clamping units 家用和类似用途低压电路用的连接器件 第2部分:扭接式连接器件的特殊要求 Connecting devices for low voltage circuits for household and similar purposes Part2:Particular requirements for twist-on connecting devices | 无 | ||
111 | IEC 61029-1, 1990 | 新沂市王庄中学GB13960-1992 | 可移式电动工具的安全 第一部分：一般要求 Safety of transportable motor-operated electric tools Part 1: General requirements | 无 | ||
112 | IEC 61029-2-1, 1993 | GB13960.2-1996 | 可移式电动工具的安全 第二部分： 圆锯的专用要求 Safety of transportable motor-operated electric tools Part 2: Particular requirements for circular saws | 无 | ||
113 | IEC 61029-2-2, 1993 | GB13960.3-1996 | 可移式电动工具的安全 第二部分：摇臂锯的专用要求 Safety of transportable motor-operated electric tools Part 2: Particular requirements for radial arm saws | 无 | ||
114 | IEC 61029-2-3, 1993 | GB13960.4-1996 | 可移式电动工具的安全 第二部分：平刨和厚度刨的专用要求 Safety of transportable motor-operated electric tools Part 2: Particular requirements for planers and thickessers | 无 | ||
115 | IEC 61029-2-4, 1993 | GB13960.5-1996 | 可移式电动工具的安全 第二部分：台式砂轮机的专用要求 Safety of transportable motor-operated electric tools Part 2: Particular requirements for bench grinders | 无 | ||
116 | IEC 61029-2-5, 1993 | GB13960.6-1996 | 可移式电动工具的安全 第二部分： 带锯的专用要求 Safety of transportable motor-operated electric tools Part 2: Particular requirements for band saws | 无 | ||
117 | IEC 61029-2-6, 1993 | GB13960.7-1997 | 可移式电动工具的安全 第二部分：带水源金刚石钻的专用要求 Safety of transportable motor-operated electric tools Part 2: Particular requirements for diamond drills with water supply | 无 | ||
118 | IEC 61029-2-7, 1993 | GB13960.8-1997 | 可移式电动工具的安全 云雨二十四式第二部分：带水源金刚石锯的专用要求 Safety of transportable motor-operated electric tools Part 2: Particular requirements for diamond saws with water supply | 无 | ||
119 | IEC 61029-2-8, 1993 | GB13960.10-1998 | 可移式电动工具的安全 第二部分： 单轴立式 木铣的专用要求 Safety of transportable motor-operated electric tools Part 2: Particular requirements for single spindle vertical moulders | 无 | ||
120 | IEC 61029-2-9, 1993 | GB13960.9-1997 | 可移式电动工具的安全 第二部分：斜切割机的专用要求 Safety of transportable motor-operated electric tools Part 2: Particular requirements for mitre saws | 无 | ||
121 | IEC 61029-2-10, 1998 | GB13960.11-2000 | 可移式电动工具的安全 第二部分：型材切割机的专用要求 Safety of transportable motor-operated electric toolsPart 2: Particular requirements for cutting-off grinders | 无 | ||
122 | IEC 61058-1, 1990 | GB15092.1-1994 | 器具开关 第一部分：通用要求 Switches for appliances Part 1: General requirements | 无 | ||
123 | IEC 61058-1, 1996 | GB15092.1-2000 | 器具开关 第一部分：通用要求 Switches for appliances Part 1: General requirements | 无 | ||
124 | IEC 61058-2-1, 1992 | GB15092.2-1994 | 器具开关 第二部分：软线开关 Switches for appliances Part 2: Particular requirements for cord switches | 无 | ||
本文发布于:2024-09-23 03:15:10，感谢您对本站的认可！
本文链接：https://www.17tex.com/xueshu/293697.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议