L exan* Resin 141R
A mericas: COMMERCIAL
UL rated HB as of 10/97. 200 series recommended when V-2 rating required. Nonhalogenated. 10.5 MFR. Internal mold release.
You may also be interested in:
Enhanced Property
Data Sheet
Improved UV SLX1432T Additonal Information Improved UV SLX1431T Additonal Information Improved Ductility EXL1414Additonal Information Improved Ductility EXL1413T Additonal Information Improved Scratch Resistance
DMX2415Additonal Information Improved HDT XHT4141Additonal Information
诗2000Improved HDT 4301Medical Grade
HP4
Additonal Information T YPICAL PROPERTIES ¹
TYPICAL VALUE UNIT STANDARD
M ECHANICAL
T ensile Stress, yld, Type I, 50 mm/min 62M Pa A STM D 638
T ensile Stress, brk, Type I, 50 mm/min 68M Pa A STM D 638T ensile Strain, yld, Type I, 50 mm/min 7%A STM D 638T ensile Strain, brk, Type I, 50 mm/min
130%A STM D 638F lexural Stress, yld, 1.3 mm/min, 50 mm span 96M Pa A STM D 790F lexural Modulus, 1.3 mm/min, 50 mm span 2340M Pa A STM D 790H ardness, Rockwell M 70-A STM D 785H ardness, Rockwell R
118-A STM D 785T aber Abrasion, CS-17, 1 kg
10m g/1000cy A STM D 1044I MPACT
Izod Impact, unnotched, 23°C 3204J /m A STM D 4812 Izod Impact, notched, 23°C 801J /m A STM D 256T ensile Impact, Type "S"
577k J/m²A STM D 1822 Falling Dart Impact (D 3029), 23°C
169
J
A STM D 3029
Source, GMD, Last Update:10/31/2000
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS
SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD C
ONDITIONS OF SALE, WHICH CAN BE FOUND AT www.sabic-ip.AND ARE AVAILABLE UPON REQUEST.ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR
RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN.Each user is responsible for making its own determination as to the suitability of Seller's products, services or recommendations for the user's particular use through appropriate end-use testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of such product, service or design in a manner that infringes any patent
or other intellectual property right.* Lexan is a trademark of SABIC INNOVATIVE PLASTICS HOLDING BV © 1997-2008 SABIC INNOVATIVE PLASTICS HOLDING BV.All rights reserved
1) T ypical values only. Variations within normal tolerances are possible for variose colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, expect the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material selection purpose.Not to be used for p art or tool design.
3) T his rating is not intended to reflect hazards presented this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
L exan* Resin 141R
A mericas: COMMERCIAL
T YPICAL PROPERTIES ¹
TYPICAL VALUE UNIT STANDARD
I MPACT
Instrumented Impact Total Energy, 23°C
63J A STM D 3763T HERMAL
V icat Softening Temp, Rate B/50
154°C A STM D 1525H DT, 0.45 MPa, 6.4 mm, unannealed 137°C A STM D 648H DT, 1.82 MPa, 6.4 mm, unannealed 132
°C A STM D 648 CTE, -40°C to 95°C, flow 6.84E-051/°C A STM E 831S pecific Heat
1.25J /g-°C A STM C 351T hermal Conductivity
0.27W /m-°C A STM C 177R elative Temp Index, Elec
130°C U L 746B R elative Temp Index, Mech w/impact 130°C U L 746B R elative Temp Index, Mech w/o impact
130°C U L 746B P HYSICAL
S pecific Gravity 1.2-A STM D 792S pecific Volume 0.83c m³/g A STM D 792D ensity
1.19g /cm³A STM D 792W ater Absorption, 24 hours
0.15%A STM D 570W ater Absorption, equilibrium, 23C 0.35%A STM D 570 Water Absorption, equilibrium, 100°C 0.58%A STM D 570M old Shrinkage, flow, 3.2 mm 0.5 - 0.7%国营企业
辞退违纪职工暂行规定
S ABIC Method Melt Flow Rate, 300°C/1.2 kgf
10.5g /10 min A STM D 1238O PTICAL
L ight Transmission 88%A STM D 1003H aze
1%A STM D 1003R efractive Index
1.586-A STM D 542E LECTRICAL
V olume Resistivity
>1.E+17O hm-cm A STM D 257D ielectric Strength, in air, 3.2 mm
14.9
k V/mm
A STM D 149
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS
Source, GMD, Last Update:10/31/2000
SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD CONDITIONS OF SALE, WHICH CAN BE FOUND AT www.sabic-ip.AND ARE AVAILABLE UPON REQUEST.ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARAN
TEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR
RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN.Each user is responsible for making its own determination as to the suitability of Seller's products, services or recommendations for the user's particular use through appropriate end-use testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of such product, service or design in a manner that infringes any patent or other intellectual property right.* Lexan is a trademark of SABIC Innovative Plastics IP BV 1) T ypical values only. Variations within normal tolerances are possible for variose colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, expect the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material selection purpose.Not to be used for p art or tool design.
3) T his rating is not intended to reflect hazards presented this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
L exan* Resin 141R
A mericas: COMMERCIAL
T YPICAL PROPERTIES ¹
TYPICAL VALUE UNIT STANDARD
E LECTRICAL
R elative Permittivity, 50/60 Hz 3.17-A STM D 150
R elative Permittivity, 1 MHz 2.96-A STM D 150D issipation Factor, 50/60 Hz 0.0009-A STM D 150D issipation Factor, 1 MHz 0.01-A STM D 150H ot Wire Ignition {PLC)
2P
第四国际
LC Code U L 746A H igh Voltage Arc Track Rate {PLC}2P LC Code U L 746A H igh Ampere Arc Ign, surface {PLC}1P LC Code U L 746A C omparative Tracking Index (UL) {PLC}
2P LC Code U L 746A F LAME CHARACTERISTICS
U L Recognized, 94HB Flame Class Rating (3)0.71m m U L 94R adiant Panel Listing
Y ES -U L Tested U V-light, water exposure/immersion
F 2
-U L 746C
Source, GMD, Last Update:10/31/2000
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIM
ER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS
酒石酸钠
SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD CONDITIONS OF SALE, WHICH CAN BE FOUND AT www.sabic-ip.AND ARE AVAILABLE UPON REQUEST.ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR
RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN.Each user is responsible for making its own determination as to the suitability of Seller's products, services or recommendations for the user's particular use through appropriate end-use testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement
Seller concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of such product, service or design in a manner that infringes any patent or other intellectual property right.* Lexan is a trademark of SABIC Innovative Plastics IP BV 1) T ypical values only. Variations within normal tolerances are possible for variose colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, expect the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material selection purpose.Not to be used for p art or tool design.
3) T his rating is not intended to reflect hazards presented this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
L exan* Resin 141R
A mericas: COMMERCIAL
P ROCESSING PARAMETERS
TYPICAL VALUE UNIT
I njection Molding
D rying Temperature 120°C D rying Time
3 - 4h rs D rying Time (Cumulative)48h rs M aximum Moisture Content 0.02
中国达人秀海派清口%M elt Temperature 295 - 315°C N ozzle Temperature 290 - 310°C F ront - Zone 3 Temperature 295 - 315°C M iddle - Zone 2 Temperature 280 - 305°C R ear - Zone 1 Temperature 270 - 295°C M old Temperature 70 - 95°C B ack Pressure 0.3 - 0.7M Pa S crew Speed
40 - 70r pm S hot to Cylinder Size 40 - 60
%V ent Depth
0.025 - 0.076
m m
Source, GMD, Last Update:10/31/2000
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS
SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD CONDITIONS OF SALE, WHICH CAN BE FOUND AT www.sabic-ip.AND ARE AVAILABLE UPON REQUEST.ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR
RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SAL
坩埚炉E, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN.Each user is responsible for making its own determination as to the suitability of Seller's products, services or recommendations for the user's particular use through appropriate end-use testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of such product, service or design in a manner that infringes any patent or other intellectual property right.* Lexan is a trademark of SABIC Innovative Plastics IP BV 1) T ypical values only. Variations within normal tolerances are possible for variose colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, expect the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material selection purpose.Not to be used for p art or tool design.
3) T his rating is not intended to reflect hazards presented this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议