Reference number ISO 17082:2004(E)
INTERNATIONAL STANDARD ISO 17082
位移比
First edition 2004-06-01
Pneumatic fluid power — Valves — Data to be included in supplier literature
Transmissions pneumatiques — Distributeurs — Données à inclure dans la documentation des fournisseurs
ISO 17082:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
sss8.aa.am超低能All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
***********************
Web
Published in Switzerland
ISO 17082:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
青藏高原土壤The main task of technical committees is to prepare International Standards. Draft International Stan dards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17082 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 5, Control products and components.
ISO 17082:2004(E)
Introduction
In pneumatic fluid power systems, power is transmitted and controlled through air under pressure within a circuit. Typical components found in such systems are pneumatic valves. These devices control flow direction, pressure or flow rate of air in the circuit.
INTERNATIONAL STANDARD ISO 17082:2004(E) Pneumatic fluid power — Valves — Data to be included in supplier literature
1 Scope
This International Standard specifies which data are to be included in the manufacturer’s supplier literature that accompanies any kind of pneumatic valve. These data are vital in selecting the proper valve for a particular application.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1219-1, Fluid power systems and components — Graphic symbols and circuit diagrams — Part 1: Graphic symbols
ISO 3448, Industrial liquid lubricants — ISO viscosity classification
门的悬念ISO 4400, Fluid power systems and components — Three-pin electrical plug connectors with earth contact — Characteristics and requirements
ISO 5598, Fluid power systems and components — Vocabulary
ISO 5599-1, Pneumatic fluid power — Five-port directional control valves — Part 1: Mounting interface surfaces without electrical connector
ISO 5599-2, Pneumatic fluid power — Five-port directional control valves — Part 2: Mounting interface surfaces with optional electrical connector
ISO 6358, Pneumatic fluid power — Components using compressible fluids — Determination of flow-rate characteristics
ISO 6952, Fluid power systems and components — Two-pin electrical plug connectors with earth contact — Characteristics and requirements
ISO 11727, Pneumatic fluid power — Identification of ports and control mechanisms of control valves and other components
ISO 12238, Pneumatic fluid power — Directional control valves — Measurement of shifting time
ISO 15217, Fluid power systems and components — 16 mm square electrical connector with earth contact — Characteristics and requirements客房管理系统设计 ISO 15218, Pneumatic fluid power — 3/2 solenoid valves — Mounting interface surfaces
ISO 15407-1, Pneumatic fluid power — Five-port directional control valves, sizes 18 mm and 26 mm — Part 1: Mounting interface surfaces without electrical connector
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议