Forestry pro measurement procedure guide
To start :开始
1,press POWER button to turn on按电源键POWER打开
林贤贞2,confirm your mode with the internal display (default is “last used” setting) 确认你的模式与内部显示(默认是“最后的使用“设置) 3,Set your desired mode and start measuring设置你想要的模式,开始测量 Mode setting：模式设置
Target priority modes目标优先模式
1、press and hold MODE button,then press and hold POWER button within 0.5 second. 按下并保持住模式按钮，然后同时按住电源按钮在0.5秒之内 2、Continue to press and hold both buttons(more than 2 seconds)until first target priority
mode and distant target priority mode are switched. 继续同时按住两个按钮(超过2秒),直到第一个目标优先模式和遥远的目标优先模式切换。
3、if the button is not pressed within 0.5 second ,the display unit<m/yd./ft.>will be switched. 如果按钮不是压在0.5秒之内,显示单元<米/码/英尺。>将切换。
Dst:Distant priority mode (factory setting) 遥远的优先模式(工厂设置)
1st:first priority mode第一优先模式
Measurement modes测量模式
Press and release MODE button. 按下和释放模式按钮
Measurement mode changes in the order of 1 (Act)to 6 (Hor)as shown below. 测量模式变化的顺序1(Act)到6(Hor)如下所示。
Holding down MODE button longer switches the display unit. 按住模式MODE按钮开关的显示装置
1.Act:linear distance特朗普不适合当总统直线距离
2.Hor(solid):horizontal distance水平距离
3.Hgt(solid):height from horizontal高度 4.Ang: angle (degrees)from horizontal角度
5.Hgt聚四氟乙烯(blinking):vertical separation(height between two points) Hgt闪动为垂直分离（两点之间高度）测试模式
6.Hor(blinking):three-point measurement (height between two points)三分测量
One-point(Act/Hor/Hgt/Ang)measurement单点测量
(measurement order:1-2-3-4-2,then repeat)测量顺序从1-2-3-4-2，然后重复
Target point目标点
Internal display(“linear distance mode”)内部展示，直线距离模式
(display will be different depending on the setting mode.)显示的不同取决模式
1.set your desired mode.设置你想要的模式
2.Aim at the target.瞄准
3.Press POWER button to measure， keeping the button pressed allows continuous measurement of up to 20 seconds. 按电源按钮保持20秒来衡量
4.Results display example of each mode结果显示每个模式的例子
（1）Act :Linear distance mode直线距离模式
（2）Hor: horizontal distance mode水平距离模式
（3）Ang:Angle mode角度模式
（4）Hgt: height mode高度模式
Power turns off 30 seconds after the last operation.停止操作30秒后，电源关闭。
External display reading instructions外部显示阅读指令
（Actual external display image）实际外部显示图像
All data below is displayed simultaneously同时显示下面数据
Act (linear distance)直线距离
Hor (horizontal distance)水平距离
Hgt(height from horizontal)高度
Ang (angle from horizontal)角度
国榷
Measuring vertical separation (height between two points) 测量垂直分离(高度两点之间)
(measurement order :1-2-3-4-5-6-7-2,then repeat) (测量顺序:1-2-3-4-5-6-7-2,然后重复)
1st target point第一目标点
2nd target point第二目标点
Internal display内部展示
1、Display when the vertical separation (height between two points)mode is selected显示垂直分离(高度两点之间)模式被选中
2、Aiming at the 1st point瞄准第一点
3、Press POWER button to measure 按电源按钮来衡量
4、Display of the height from horizontal level of 1st point显示从水平线到第一点的高度
5、Aiming at the 2李雯nd target point针对第二点目标
6、Press POWER button to measure按电源按钮来衡量
7、Display of the vertical separation (height between two points)显示两点之间高度
（This symbol indicates the display is blinking显示器闪烁符号）
External display reading instructions外部显示阅读指令
After the measurement of 1st target point
(actual external display image)
After the measurement of 2st target point
(display of the vertical height between two points)
(actual external display image)
Three –point measurement (height between two points)三分测量（高度两点之间）
(measurement order :1-2-3-4-5-6-7-8-2,then repeat)
1st target point
2nd target point
3rd target point
When measuring 2nd and 3rd points please note that angles should be between -75°and +75°from the horizontal level .if measurement fails ,the angle is beyond ±75°当测量第2和第3点请注意,-75°之间的角度应该和+ 75°的水平。如果测量失败,75°±角超出
Internal display
1、Display when three point measurement mode is selected显示当三个点测量模式被选中2、Aiming at the 1st point .瞄准第一点
3、Press POWER button to measure按电源按钮来衡量
4、Display of the horizontal distance to the 1st point.显示第一点水平距离
5、Aiming at the 2nd target point.瞄准第二点
6、Press POWER button to measure按电源按钮来衡量
试行条例7、Display of the vertical separation (height from horizontal level to 2nd point). 显示垂直分离(高度从水平到第二点)。
8、Aiming at the 3rd target point.瞄准第三点
9、Press POWER button to measure按电源按钮来衡量
10、Display of the vertical separation (height between 2nd and 3rd points) 显示垂直分离(第2和第3点之间的高度)
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议