三星SCX-4300一体机芯片解码操作说明

防爆恒温恒湿

一台4300，显示墨粉用尽，更换墨盒，无法打印，红灯亮。机器被锁定。

A Samsung SCX 4300 printer, when the screen shows “Toner Empty, Replace

Toner cartridge”, the red light is on, the printer is locked.

首先将打印机连上电脑。然后启动打印机。等预热完毕后。电脑应该能检测出打印机的状态。运行软件.

At first connect your printer with the PC then start your printer. Waiting for your printer finish warm-up, the PC can detect the status of your printer, running the software.

点击开始进入保安接线排 Click “ 开始” enter：

芯片破解

打印机应该依次显示：

Your printer should show in turn:

PC TO DRAM IS OK聚酰亚胺纤维 (如果显示PC TO DRAM IS NG 现浇箱梁施工不能传输到打印机。打印机主板芯片的版本不对）

PC TO DRAM IS OK (If it shows PC TO DRAM IS NG are not able to transfer to the printer. Then the version of motherboard chip is not right.水泥砖制砖机）

FLASH IS ERASING

FLASH PROGRMMING

然后打印机重新预热。预热完成后修改完成。

Then the printer will warm-up again. When it finish, the modification

is finished too.

清零操作：Clearing zero operation:

菜单（Menu）->10.Maintenance（维护）-->Clear Settings（清除设置）-->All Settings（所有设置）-->OK(确定)

操作后打印机灯会闪几下，然后恢复正常的绿，电脑墨粉状态条满格，完成清零。

The printer’s light will be flashing after the operation, then turn into normal green, it’s full at toner bar on computer, finish clearing zero.

以后当机子显示粉墨不足或刚加粉时就操作一次。机子就恢复成满粉状态。

In future when the printer shows short of toner or after adding toner, operate it as above, the printer will return to full toner.

当打印变淡时注意及时加墨粉。

Remember to add toner when the printing turn into light color.

加粉必须自己操作。打印机可没有自动加粉的功能。

You need to add toner by yourself. Printer have not the function of adding toner automatically.

QQ 604769802

重要说明Important specifications：

破解的方法：

1、将打印机连接到电脑。

2、启动打印机并等预热完毕。这时电脑应能检测到打印机状态。

3、运行"SCX4300计数解码固件.exe",点击开始。然后程序自动运行。过两分钟左右，当退出按钮生效后点击退出。完成破解。

1. Connect the printer to a computer.

2. Turn on the printer and waiting for finishing the warm up. At this time, the computer can check out the printer’s status.

3. Run”SCX4300 Counting ”. click “start”, then the program will run automatically. After two minutes, click “ exit “ when it turns up. Finish decoding.

清零操作：

连续按菜单（Menu）->10.Maintenance（维护）-->Clear Settings（清除设置）

-->All Settings（所有设置）--> 按OK（确定）键

注：每清零一次大约可以打印1千页。一般鼓内的粉可打印约2-3千页。

Remark: It can print 1000 pages after clearing zero. Usually it can print 2000-3000 pages with the toner in the cartridge.

破解并清零后仍显示粉末不足的解决办法：

After cracking and clearing the printer still show the toner is not enough, what should you do:

本文发布于:2024-09-22 01:25:17，感谢您对本站的认可！

本文链接：https://www.17tex.com/tex/4/334868.html

上一篇：EPSON系列打印机芯片破解工具

下一篇：无限Wifi网络破解——BACK TRACK支持的网卡芯片