井场标示翻译

Must wear personnel protective equipment when in location.进入井场必须劳保穿戴齐全
高频变压器参数(Operate the personnel must wear the gloves. 操作人员必须戴手套。)
地址匹配
Be familiar with escape route and muster point.熟悉逃生路线和应急集合点
(emergency muster 紧急集合)
Must be in command of location personnel when in location.进入井场接受现场人员的指挥
Automatically abide by HSE regulation.自觉执行现场HSE管理规定
No smoking and no burning in location.井场内严禁吸烟和动用明火
No taking in dangerous materials without permit.未经允许禁止携带危险品进入
No entering into high voltage area without permit.未经许可禁止进入高压危险区
马蹄去皮机
Prohibiting randomly starting running equipment and appliance.禁止虽已启动运转设备、电器
Prohibiting randomly moving safety device and alarming device.禁止随意移动安全、报警设施
Gather to muster point by specified route when emergency.应急情况按指定路线撤至集合点
Emergency signal: one long alarming or a aloud cry.应急信号:一声长笛或大声呼喊
缘114
Check the pump liner and pistons. 检查一下缸套和活塞。
Explosionproof light.防爆灯
lubricant oil 润滑油
engine oil 机油
雨棚梁Diesel Engine柴油机
Oil filter 机油过滤器
loosen a screw 松开螺丝
tighten up a screw 拧紧螺丝
风管抗震支吊架A usually thin nut screwed down on another nut to prevent it from loosening 防松螺母常指拧紧在另一个螺母上的防止其松动的细螺母
Kelly 方钻杆
tubing elevator 油管吊卡
Desander 除砂器. Degasser 除气器. Centrifuge 离心机. Mud Agitator 泥浆搅拌器. Shale Shaker振动筛.
Optional parts ary hose,elevator link,hydraulic tong ,air spiders,lelly bushivg,rotary table and substructure (with ramp and oadder)etc. 选配件包括水龙头和水龙带、吊环、液压大钳、气动卡盘、转盘、钻台(带滑道和梯子)等。
The rigs indlude special carrier(developed by our company),engine,hydraulic transmissio
n,right angle gearbox,single (double)drum drawwork,rotary table transmission box,hydraulic drawworks,front and rear supporting frame,double-section hydraulic telescopic mast,crownblock,travelling hool,weight indicator,hydraulic,pneumatic and electrical system,etc. 专用底盘为载车,由专用汽车底盘、发动机、液力变速箱、角传动箱、单(双)滚筒绞车、转盘传动箱、液压绞车、前支架、后支架、双节液压伸缩式井架、天车、游车大钩、指重表、液压系统、气路系统、电器系统等组成。

本文发布于:2024-09-21 22:05:18,感谢您对本站的认可!

本文链接:https://www.17tex.com/tex/4/207137.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:液压   进入   系统   禁止
留言与评论(共有 0 条评论)
   
验证码:
Copyright ©2019-2024 Comsenz Inc.Powered by © 易纺专利技术学习网 豫ICP备2022007602号 豫公网安备41160202000603 站长QQ:729038198 关于我们 投诉建议