液压升降台设计说明书

学校代码：10410

序号：055020

本科毕业设计

题目：液压升降台

江西农业大学毕业设计(论文)任务书

绝对式角度编码器废水处理有机系统

设计（论文）课题名称	液压升降台设计
学生姓名		院（系）	工学院	专业
指导教师	龚水泉	职称	副教授	学历	本科
毕业设计（论文）要求：有以下图纸和技术文件：装配图零件图液压原理图零件表液压元件表标准件表设计说明书
毕业设计（论文）内容与技术参数：设计一台液压升降台主要技术参数如下：幅面 2600×1400 mm 起升最大重量 3T 起升最大高度 800mm
毕业设计（论文）工作计划：
接受任务日期 2009 年 2 月 18 日要求完成日期 2009 年 5 月 20 日学生签名年月日指导教师签名年月日院长（主任）签名年月日

摘要

扫路刷

本次设计任务是液压升降台，它是一种升降稳定性好，适用范围广的货物举升设备。其起升高度800mm，举升重量3T，幅面尺寸2600×1400 mm.其动作主要是由两个双作用液压缸推动“X”型架，带动上板移动来实现的。该液压升降台主要由两部分组成：液压部分和机械部分。设计液压部分时，先确定了液压系统方案。选择液压基本控制回路时，换向回路选择三位四通电磁换向阀；平衡回路选择用液控单向阀。确定各种基本回路后，又确定了液压系统传动形式，拟定液压系统原理图，然后对液压元辅件进行了设计、选择，并对其进行校核。经过计算后液压缸直径选定为70毫米，液压泵选叶片泵。根据系统工作的最大功率选Y90S-4三相异步电动机。在确定泵后，又对其他的元辅件进行了合理的选择，最后确定阀块的设计及效率计算。机械部分主要由上板架、下板架、内连杆和外连杆四部分组成。通过设计、选择机械部分材料与结构，并对其进行受力分析与强度校核，结果证明机械部分结构设计可以满足要求，进一步完成了本次设计题目。

关键词：液压；升降平台；上板架；下板架；内连杆；外连杆

hydraulic lift platform

Abstract:The task of this羟基氧化钴 design is hydraulic lift platform, it is an carpo lifting equipment with good stablity of taking off and landing. Its lifting height is 800mm, weight lifting is three tons, and frame size is 2600 × 1400 mm. Its action is mainly composed of two pairs of hydraulic cylinders to promote the "X" aircraft, leding to realize the mobile plate.The hydraulic lifting platform is mainly composed of two parts : hydraulic parts and mechanical parts. In the design of the hydraulic parts, I first made sure the hydraulic system. In the process of selecting the basic of hydraulic control loop , the direction loop I chosen to use three position four-way electromagnetic valve,and the balance loop I chosen to use pilot-controlled check value. 人货电梯防护门After the identification of the basic loop, I also made sure the form of hydraulic transmission system, the development of the hydraulic system schematic diagram, and then I designed,selected the hydraulic components and accessories, and checked them. After calculating I selected two 70 mm hydraulic cylinder, I selected the vane pump as the hydraulic pump.柴油燃烧器 According to the maximum power of this system I chosen Y90S-4 three-phase asynchronous motor. After determining the pump, I

also chosen the other components and accessories reasonly and finaly I designed the valve block and calculated the efficiency. The mechanical parts is mainly composed of inside and outside link and On board aircraft, the next board aircraft. Through the design, choice of materials and the structure and after the stress analysis and strength of their check, the results proved that the mechanical parts can satisfy the design requirements,which further completed the design of the subject.

Key words: Hydraulic; take-off and landing platform;Inside and outside link

本文发布于:2024-09-23 22:31:36，感谢您对本站的认可！

本文链接：https://www.17tex.com/tex/4/162390.html

上一篇：螺旋升降电梯制动器的机械松闸设备的生产技术

下一篇：剪叉式高空作业平台检查验收表

标签：液压部分设计选择系统机械回路

留言与评论（共有 0 条评论）