(一)模具专业基本用词 Professional Terms
1. 塑料 — plastic, resin
2. 样件 — sample
3. 钢料 — steel
4. 注塑机 — injection machine, press
5. 产品 — part, product, moulding 6. 模具 — mold, mould, tool
A 简易模(样板模)— prototype mold B 量产用模具 — production mold
7. 三维造型(数模)—3D model, 3D data
8. 二维产品图 — 2D part drawing
9. 设计 — design
10. 制造 — manufacture, build up, construction
11. 检验 — check, inspection
12. 测量 — measure, inspection
13. 修改 — change, modify, correction
14. 工程更改 — engineer change
15. 质量 — quality
16. 数量 — quantity
锅炉冷渣机
17. 基准 — datum, reference
(二)如何解析2D 产品图?How to read 2D part drawing?
一. 产品几何 Geometry
1.点 — point
2.线(边) — line, edge
3.面 face
A 侧面 — side B 表面 — surface C 外观面 — appearance surface
4.壁厚 — wall thickness, stock thickness
5.加强筋(骨位) — rib
6.孔 — hole
7.细长的槽水晶笔筒 — slot
8.柱位 — boss
9.角 — corner
A 圆角 — fillet B 倒角 — chamfer C 尖角 — sharp corner
10.斜度 — angle, taper
11. 凹槽—recess , groove
二. 分模信息 Splitting
1. 分型线 — parting line (P/L), splitting line
2. 主分模方向 — main direction, line of draw
3. 浇口设定 — gating
三. 产品标识 Part Identification
1. 产品名称 — part name (P/N)
2. 产品编号+版本号 — part number + revision (Rev.)
3. 型腔号 — cavity number
4. 材料标记 — material symbol
5. 模具编号 — mold number (no.)
6. 日期印 — dating insert, date code
7. 循环印 — cycling code
8. 公司标志 — company logo
四. 技术要求 Specification (Special Requirement) 1. 项目启动表 Kick-off sheet
1) 项目名称 — program name, project name
2) 产品名称 — part name, product name, part description
3) 产品编号 — part number (P/N)
4) 客户模号 — customer mold no.
5) 项目启动日期 — kick off date, start date
6) 项目完成日期 — due date, lead time
7) 内模件用钢 — tool steel
8) 型腔数量 — number of cavities
9) 数据文件编号 — data file no.
10) 注塑材料 — resin, plastic, raw material
11) 收缩率 — shrink, shrinkage, shrink factor
12) 注塑机吨位 — molding machine size, injection machine size
13) 成型周期 — cycle time
14) 型腔光洁度 — cavity polish
15) 型芯光洁度 — core polish
16) 皮纹(晒纹)— texture, grain
更衣凳
17) 拔模斜度 — draft angle, removal taper
18) 注塑件颜及光泽 — molded color & gloss
19) 模具加工地 — manufacturing facility
20) 热流道供应商 — manifold manufacturer, manifold supplier
21) 浇口位置 — gate location / position
22) 浇口类型 — gate type
23) 产品标识 — stamp information, part identification
24) 特殊要求 — special instructions
2. 产品质量及外观要求 Part Quality & Appearance Requirement
1) 尺寸及公差 Dimension & Tolerance 1 重要尺寸 — critical dimension, important dim., key dim.
2 抽纸机理论尺寸 — nominal dimension
3 实际尺寸 — actual dimension
4 公差 — tolerance
5 公差带 — tolerance range
6 尺寸超差 — dimension deviation
7 接受(合格) — accept, OK
8 拒绝(不合格) — reject, refuse, obsolete, NG
9 让步接受 — concession, special admit
10 返工 — re-work
2) 产品缺陷(常见的)Defects (normal)
1 缩水 — sink mark, shrinkage
3 段差 — mismatch discrepancy
4 银丝纹,蛇纹 — snake marks, streak
5 弯曲,变形 — warpage, distortion
6 打不饱(缺料) — short shot
染酸
7 熔接线 — weld line
8 多胶— unwanted plastic
9 拉伤—damage
3. 产品外观 Part Appearance
1 产品颜 — part color
2 产品光泽 — gloss
3 皮纹粒度 — grain
4. 常用词汇、词组及短语 Normal Word, Short Sentence
1) 单边 — per side
2) 双边 — both sides
3) 加入,添加 — add, incorporate
4) 去除,取消 — remove, cancel
5) 满足…的要求,符合,与…要求一致 — according to, conform to, satisfy, meet
6) 要求,需要 — require, need, demand
7) 确认 — be approved, agreed by …
8) 允许 — permit, allow
9) 在…范围之内 — within
10) 不可以,不允许,禁止 — free from, prevent, avoid
11) …,除非有另指 — … unless otherwise specified
12) …或少于 — …or less
13) 自动化运作 — automatic operation
14) 未注尺寸(详细形状)见三维造型
Non dimensioned contour (detailed shape) see 3D model.
15) 分型线上的飞边(披缝)或段差应小于…
Burrs or discrepancy on the P/L shall be … or less.
五. 标题栏 Title Block
1. 产品名称 — part name
2. 图纸编号 + 版本号(索引号)— drawing no. + level (index)
3. 一般公差 — general tolerance
(三) 如何阅读制模标准?How to read tooling standard?
一.模具结构术语 Mold Construction Terms
A.模架 Mold Base
1. 模架量化特征 Measurement Feature
① 长 X 宽 X 高 — Length X Width X Height
② 模具高度尺寸(模厚) — stack height of mould
③ 模具重量 — total weight of mould, mould thickness
2. 定模底板 — front plate, top clamping plate, clamp plate, clamping plate
3. 定模板 — cavity plate, fixed mould plate, A – plate
4. 动模板 — core plate, moving mould plate, B – plate
5. 支撑板 — support plate, backing plate
6. 间隔板,方铁 — support blocks, rails, risers, spacer block
7. 顶杆固定板 — retaining plate, ejector retaining plate
8. 顶板 — ejector plate,bottom clamping plate
9. 动模底板 — back plate
10. 导柱 — guide pillar, leader pin, guide pin
11. 导套 — guide bush, leader pin bush
12. 复位杆 — return pin, push-back pin
13. 弹簧 — spring
14. 撑头四技术 — support pillar
15. 顶针板导柱、导套 — ejection guide pin / bush
16. 垃圾钉 — stop pin, stop button
17. 模脚 — standing-off pillars
18. 标牌 — plaque scutcheon
B.成型零部件 moulding components