FORM APPROVED Contact: info@diamondfasteners
OMB NO. 0704-0188
. FORM APPROVED
OMB NO. 0704-0188 NOTES:
1.DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE; DECIMALS ± .010 AND ANGLES ± 0.5.
2.BREAK SHARP EDGES AND CORNERS AND REMOVE AU. BURRS AND SLIVERS.
3. THE -3 SIZE BEARING IS EXEMPT FROM THE "RADIAL STATIC UNIT LOAD” TEST BECAUSE THE LOAD CAPACITY OF THE BEARING IS PIN CRITICAL
4.WHEN TESTED TO THE FLUID CONTAMINATION AND SUB-ZERO TEMPERATURE REQUIREMENTS OF THE PROCUREMENT SPECIFICATION.THE OSCILLATING LOAD SHALL BE DECREASED TO 75% OF THE SPECIFIED LOAD.
5. WHEN FLUIDS AND ELEVATED TEMPERATURES (ABOVE 200° F) ARE BOTH PRESENT IN AN Application, THEN Reductions IN OPERATING LOADS OR BEARING LIFE MAY BE REQUIRED.
6. DASH NUMBER Designates NOMINAL BORE DIA IN SIXTEENTHS OF AN INCH.
7. DIMENSION "D" TO BE MET AFTER PLATING. DIMENSION “H"TO BE MET BEFORE PLATING WHEN APPLICABLE.
8. EXAMPLE OF PART NO.
MS14101 -6 C P K T = .375 NOMINAL BORE DIA PH13-8Mo BALL MATERIAL ZINC-NICKEL PLATED, LOW TORQUE, .010 INCH T OVERSIZE O.D., (DIMENSION D).
ABSENCE OF THE LETTERS ”T"- AND ”U“INDICATE STANDARD OUTER DIAMETER (D), (SEE TABLE 9.
T - .010 OVERSIZE D (FOR REPAIR ONLY, SEE TABLE II).
u = .020 OVERSIZE D (F OR REPAIR ONLY , SEE TABLE II).
ABSENCE OF THE LETTER “K" INDICATES STANDARD BREAKAWAY TORQUE (SEE TABLE l). “
LETTER "K“ INDICATES LOW BREAKAWAY TORQUE (SEE TABLE l).
ABSENCE OF THE LETTER “ P “ INDICATES NO PLATING.LETTER “P" INDICATES ZINC-NICKEL OR CADMIUM PLATING (SEE REQUIREMENT 4).
ABSENCE OF THE LETTER "C“ INDICATES 440C BAIL MATERIAL.
msinfo
LETTER l C “ INDICATES PH13-8Mo BALL MATERIAL.
SIZE - BORE DIAMETER (DASH NO. FROM TABLE l).
MS NUMBER.
8a. BALL MATERIAL SHALL BE 440C AMS-5630 UNLESS “C“CALLOUT IS PRESENT IN PART NUMBER. "C“ INDICATES PH13-8Mo
AMS-5629 H1000.9. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCE CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE.
10.REFERENCED GOVERNMENT (OR NON-GOVERNMENT) DOCUMENTS OF THE ISSUE LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS DODISS SPECIFIED IN THE SOLICITATION FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN.PREPARING ACTIVITY: NAVY - AS MILITARY SPECIFICATION SHEET
SPECIFICATION SHEET NUMBER CUSTODIANS: ARMY-AV M S 14101REV J
NAVY- AS 5 DEC 94AIR FORCE-99DLA-TITLE BEARING, PLAN, SELF-LUBRICATING,SUPERSEDING
REV H REVIEW: ARMY-AR, AT, ME, DLA-IS, USAF-84SELF-ALIGNING LOW SPEED, NARROW,M
S1410124 JAN 9GROOVED OUTER RING, -65’ TO 325’ F PROJECT NUMBER 3120-0742-05AMSC -N/A FSC 3120DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.PAGE 3OF 3Contact: info@diamondfasteners
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议