天线英语

1. 防落角钢:anti-falling angle iron
2. 微调拉杆:fine adjusting rod
3. 加强杆:Stabilizing arm; strengthening rod
4. 方位:azimuth
5. 锁紧:lock  拧紧:fasten    松掉:loosen  拆卸:remove    安装mount;install  卸载:unload  旋转:rotate
6. 活扳手:adjustable wrench
7. 十字头螺栓:cross headed bolts
8. 力矩扳手:torque wrench
9. 支座:pedestal    方位座:azimuth pedestal
10. 馈源支撑杆:feeder support rod
11. 平垫:flat washer    弹垫:spring washer
12. 压块:pressing block
13. 组件:component (如汽车的轮胎)
附件:accessory(如汽车的收音机)
零件:part(如汽车的螺丝)
14. 防锈的:anti-rust
15. 型号与规格:model and specification
16. 出口接口界面:interface
17. 拉线:guy wire kit (防止因馈源长度过长而导致倾斜)
18. 斜垫圈:bevel washer、oblique washer(之前用过)
19. 接缝:seam  接头:joint  连接处:junction
20. 相对应的:corresponding
21.与..对齐: be aligned with
22. 将天线罩布平铺在天线口面上:spread the radome onto the reflector
23. 打开,展开:unfold
24. 吊钩:lifting hook/hoisting hook(用过)
25. 防卡死剂:anti seize paste
污水池覆盖26. 套管:casing pipe (not confirmed)
27. 具有支撑能力的构件:sustainable frame
28. 现场条件:site condition
29. 夹板:clamp
30. 向前或者向后移:move forward or backward
31. 合路器:coupler
37. 备用ODU: standby ODU
38. 刀片:blade    刮:scrape
39. 硅橡胶:silicon rubber
40. 按照:as per
41. 交叉极化鉴别率:XPD(cross polarization discrimination)
42. 前后比:F/B ratio
43. 隔离度:isolation
44. 驻波比:VSWR
45. 包络图:envelope(RPE基础上人为概括)
方向图:RPE (radiation pattern envelope)
46. 轴向力:axial force      侧向力:side fForce
47. 扭矩:twisting moment
The axial, side and twisting moment forces stated are maximum loads applied to the tower by the antenna at a survival wind speed of 250 km/h (70m/s). They are, in every case, the result of wind from the most critical direction for each parameter. The individual maximums may not occur simultaneously. All forces are referenced to the antenna mounting pipe.
表格中所列轴向力、侧向力与扭矩均为极限风速250 km/h
(70m/s)下天线所承受的最大载荷。所有力均作用于铁塔上,因
各项参数的最大值是在不同风向下测得,所以各最大值不会同时
发生。
48. HV- 水平极化接口接收垂直极化信号
HV- response of a horizontally polarized port to a vertically polarized signal
49. 压铸铝合金:die-casting aluminum
50.  IEC: International Electrotechnical Commission
51. 天线:base station antenna
52. 蜂窝天线:cell base station antenna
53.  OEM: original equipment manufacturer 原始设备生产商贴牌生产
三维试衣
54. 三角支撑腿:triangle supportive leg
55. 钢丝绳:steel wire
40.  Vacuum  'vækjʊəm  n./adj./vt. 真空(的)
47. 自攻螺钉:tapping Screw          膨胀螺钉:expansion bolt
48.  MTBF: Mean Time between Failures 平均故障时间
49.  attenuate 减弱(的); attenuation    n.衰减变薄稀释
50.  flammability 可燃性易燃性
51.  keel  n./vt. 龙骨,翻转
52.  U-steel 槽钢
53.  terminal strip  接线板;端子板(相当于terminal board)
54.  socket  插座      socket Screw  凹头螺钉
55.  断路器:circuit breaker
56.  magnetic  有磁性的            magnetic valve 电磁阀
57.  矢量  vector              标量  scalar
56.  集装箱:container
57.  麻花钻: twist drill
58.  手钻: pistol drill
60.  通信容量:traffic capacity
61.  XPIC:cross polarization interference counteracter  交叉极化干扰抵消器
62.  N/A  not applicable 不适用
63.  ambient temperature 环境温度
64.  dielectric coaxial cable绝缘同轴电缆
65.  longitudinal uniformity 纵向均匀度
66. 变换:Transition
连接盘:connecting plate
转换盘:transforming plate
固定盘:fixing plate
67. 塑粉:molding powder
68. oxide:氧化物
Oxidation 氧化氧化反应
Oxidize: v.使氧化氧化
Oxide layer:氧化层
69. 铝铸件:aluminum casting
氧化铝: aluminum oxide
70. 驻波比:VSWR voltage standing wave ratio
物理除垢71. 方向性:directivity
72. 防锈铝合金:anti-rust aluminum alloy
73. 防腐液:preservative liquid
74. 整改费用:rectification cost
75. 结构件:framework component
76. 备用件:standby part
78. 替换件:replacement part
79. 后备圈:back ring (collar)
80. OMT极化分离器:(orthogonal mode transducer )(polarization polarizer)
方波信号发生器81. 失配损耗:mismatch loss
82. 传输线:transmission line
83. 无源中继反射板:passive relaying reflector
84. 直扣式天线:direct mounting antenna
85. 微波器件:microwave accessories
86. 合路器统一为coupler    圈统一为ring  后馈统一为back feed
87. 花栏箱:crate  纸箱 carton  铁皮胶合板箱(耐凡包装箱):plywood case
88. 低剖面:low profile
浅锅: shallow dish
89. 多层板:plywood
58. 堆码试验 stack test
59. impedance 电阻
60. dipole  偶极双极子
61. (潘通卡)formula guide 配方指南
Solid coated 光面铜版纸
62. 麻花钻头:twist drill
63. 布垫:cloth pad
64. 覆盖叠加:overlay
65. bore sight  瞄准线轴向
66. swan neck 弯波导    superimpose 重叠
67. amplitude  振幅
68. warp  弯曲变形(罩板弯曲变形)
69. deviation 偏差偏离
70. asymmetry 不对称
70. FOC: free of charge  免费
71. as per 按照依据
72. 有源元件:active element
无源元件:passive element
73. 铣工:mill    车工:lathe
旋压:spin
90. 免熏蒸多层板封闭箱: fumigation-free plywood case
91. 附表:attachment
92. 落水孔:draining hole
六足机器人93. 插芯:insertion core
94. 固定卡:fixing clamp
95.  radio意思为单元设备
96.  ETSI:European telecommunication standards institute 欧洲电信
标准协会
97. 通孔:through hole
98. 均布:uniform distribution
99.  RF:radio frequency  射频
100. P-mount  挂架
Reflector support plate 中心盘
101. ASD:acceleration spectrum density  加速度频谱密度
102. RRS:required response spectrum  所需响应频谱
103. zero period acceleration  零周期加速度
104. 箱撑 supporting batten
105. 包装箱底座:case base
气浮垫
106. 校核: proofreading
107. 设计:designer  校队:press-corrector  评审:assessor  批准:approver
108. 自由跌落试验:free fall test
Topping around 侧翻试验
109. RMS:root mean square 均方根
111. 挂架:hanging bracket
112. 组装:assembly
113. 安装:installation
114. 侧罩:shield
115. 防落角钢:anti-fall clamp
116. 吊装:hoisting
117. 加强杆:首選stabilizing arm /strengthening rod
118. 极化:polarization
119. 方位:azimuth
120. 俯仰调整:elevation adjustment
121. 抛物面天线:parabolic antenna
122. 安装手册:installation annual
123. 矩出口:antenna rectangle interface
124. 圆出口:antenna circle interface
125. 变形:deformation
126. 最佳状态:optimum performance
127. 抱杆:mounting pipe
128. 固定:fix;attach
129. 垂直地:vertically
130. 支撑点:fixing point

本文发布于:2024-09-23 11:20:20,感谢您对本站的认可!

本文链接:https://www.17tex.com/tex/3/277048.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:天线   试验   汽车   设备   覆盖
留言与评论(共有 0 条评论)
   
验证码:
Copyright ©2019-2024 Comsenz Inc.Powered by © 易纺专利技术学习网 豫ICP备2022007602号 豫公网安备41160202000603 站长QQ:729038198 关于我们 投诉建议