Hollyland (China) Electronics
本规格书适用于本公司生产并获得CQC 、UR/CUR 、SEMKO 、PSE 、VDE 、BSI 、KC 认证的5ET RoHS 系列HOLLY 商标的超小型保险丝。This specification defines the technical requirements of sub-miniature fuse type 5ET RoHS series with HOLLY ® 产品部件号为： brand, which are approved by CQC, UR/CUR, SEMKO, PSE, VDE 、BSI and KTL. 型号 额定电流 额定电压 Construction of part no: type rated current rated voltage 5ET 0100 H A
型号规格： 型号 特性符号 额定电流 MODEL DETAIL: 额定电压 Type Characteristic Symbol Rated Current 例如/ Example: Rated Voltage 5ET T 2 A *特性符号/ Characteristic Symbol: T – 慢断型/ Time-Lag.
250V
2. 相关标准及认证情况/ APPLICABLE STANDARDS & APPROVED DETAILS 2.1 5ET RoHS 系列产品适用的相关标准是 IEC 60127和GB 9364。
Applicable standards for 5ET RoHS series are IEC 60127 and GB 9364.
Hollyland (China) Electronics
3. / ADDRESS
中国福建省厦门市湖里区枋湖路9-19号
NO. 9-19, FANGHU ROAD, HULI, XIAMEN, FUJIAN, CHINA.
4. 构造图/ CONSTRUCTION FIG . & DIMENSION
4.2 方形塑料帽/ Square THERMOPLASTIC CAP 方形塑料帽无破裂、缺损或污染等现象。 Square Thermoplastic Cap shall have no defects such as crack, injury and contamination. 4.3 塑料件阻燃性能/ FLAMMABILITY CIASSIFICATION: UL 94V-0. 5. 机械特性/ MECHANICAL PERFORMANCES
乳化石蜡保险丝应能承受下列二项试验。Fuse shall withstand the following two tests. 5.1 拉力试验/ TENSILE TEST
将保险丝保持在一个固定的位置，沿引线方向施加10N 的拉力，引线、方形塑料帽不能松动并且方形塑料帽不应破裂。When fuse is fixed and the tensile force 10N is applied in a direction to lead, no looseness of leads and square thermoplastic cap or damage of square thermoplastic cap shall occur. 5.2 推力试验/ THRUST TEST
将保险丝保持在一个固定的位置，沿引线方向旋加2N 的推力，引线、方形塑料不能松动并且方形塑料不应破裂。When fuse is fixed and the thrust 2N is applied in a direction to lead, no looseness of leads and square thermoplastic cap or damage of square thermoplastic cap shall occur.
6. 电气特性/ ELECTRICAL PERFORMANCES 6.1 测试条件/ TEST CONDITIONS A 全部测试条件都应在环境温度24℃±3℃条件下进行，在此期间温度变化不允许达到+5℃和到极限范围。 All electrical tests are conducted at a ambient temperature of 24±3℃. The ambient temperature is not allowed
Remark: ① S quare Thermoplastic Cap ②
S quare Base Long Lead Short Lead 7.2备注：①方型塑料帽 ②方型底座
长引线 短引线
Hollyland (China) Electronics
to vary more than 5℃ during the test, and must be within these limits.
B 每个保险丝支架，水平安装在不导电的胶木测试板上，以便被测的保险丝在测试板上能保持水平。
肩垫Each fuse-holder is to be mounted horizontally on a test board of non-conducting bakelite, so that each fuse under test is held in a horizontal position above the board .
6.2 电压降、平均I 2
T 值(供参考)、吸油烟机止回阀
最大持续功耗/ VOLTAGE DROP , AVERAGE I 2
T VALUE (FOR REFERENCE ONLY)
双向节流阀
6.3 负载能力测试/ CURRENT-CARRYING CAPACITY TEST
当保险丝通以150%倍额定电流的条件下进行测试时，在1小时内电路不应断开，保险丝不被电流熔断，方形塑料帽不破裂、脱落。A fuse shall carry 150% of rated current for 1 hour or more, and the circuit shall not be opened. While the fuse is carrying this current, no open circuit, melt fusible element, and square thermoplastic cap shall not be charred or ruptured in any manner.
6.4 预飞弧时间-电流特性/ PRE-ARCING TIME-CURRENT CHARACTERISTICS
当保险丝通以下表规定的电流时，其熔断时间必须符合下表的要求，且方形塑料帽不能飞脱、损坏。When the current in the following table is passing the fuse, its opening time must be in accordance with the requirements in the following table, that is, the pre-arcing time. Moreover, there shall be not damaged or shattered of the square thermoplastic cap.
6.5 分断能力/ BREAKING CAPACITY
保险丝的分断能力应能达到下表规定的相应的各种安全认证的分断能力要求。保险丝分断电路后，方形塑料帽不应飞脱、损坏。The breaking capacity should reach the rated breaking current given in the following table. And after this test, there shall be not damaged or shattered of the square thermoplastic cap.
Hollyland (China) Electronics
鸟笼灯Hollyland (China) Electronics
6.7 平均I2T-T特性曲线图(供参考)/ THE A VERAGE I2
连通区域T-T CHARACTERISTICS CURVE(FOR REFERENCE ONLY)
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议