G U 1086
1.5A Low Dropout Positive Adjustable or Fixed-Mode Regulator
Description
The GU1086 is a low dropout positive adjustable or fixed-mode regulator with minimum of 1.5A output current capability. The product is specifically designed to provide well-regulated supply for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply. GU1086 is also well suited for other applications such as VGA cards. GU1086 is guaranteed to have <1.4V dropout at full load current making it ideal to provide well-regulated outputs of 1.25 to 5.0V with 4.7 to 12V input supply by different output voltage.
Features
3-Terminal Adjustable or fixed 1.5V,1.8V,2.5V,3.3V,5.0V 1.4V Maximum Dropout at Full Load current Fast Transient response Built-in Thermal Shutdown Output current limiting
Package Dimensions
Millimeter
Millimeter
REF . Min. Max. REF .
Min. Max. A 4.40 4.80 c2 1.25 1.45 b 0.76 1.00 b2 1.17 1.47 L4 0.00 0.30 B D 8.6 9.0 c 0.36 0.5 e 2.54 REF . L3 1.50 REF . L 14.6 15.8 L1 2.29 2.79 0˚ 8˚ E
永磁马达9.80 10.4 L2
1.27 REF .
Typical Circuit
Block Diagram
Pin Descriptions
Name I/O Pin# Function
Adj (GND) 1 Adjustable (Ground only for fixed mode)
Vout O 2 The output of the regulator. A minimum of 10uF capacitor must be connected from this pin to
ground to insure stability.
电动画舫船
Vin I 3 The input pin of regulator. Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be 1.4V higher than Vout in order for the device to regulate properly.
Absolute Maximum Ratings
Symbol Parameter Ratings Unit V in DC Supply Voltage-0.3 to 12V P D Power Dissipation Internally Limited
T ST Storage Temperature -65 ~ + 150 T OP Operating Junction Temperature Range 0 ~ + 150
Electrical Characteristics
Parameter Conditions MIN TYP MAX UNIT Reference Voltage GU1086-ADJ Io=10mA, T J =25,
(Vin-Vout )=1.5V 1.225 1.250 1.275 V GU1086-1.5 Io=10mA, T J =25,
瓜子烘干机3.0V Vin 12V 1.470 1.500 1.530 V GU1086-1.8 Io=10mA, T J =25,
3.3V Vin 12V 1.764 1.800 1.836 V
黑发液
GU1086-2.5 Io=10mA, T J =25,
4.0V Vin 12V 2.450 2.500 2.550 V
GU1086-3.3 Io=10mA, T J =25,
4.8V Vin 12V 3.235 3.300 3.365 V Output Voltage
GU1086-5.0 Io=10mA, T J =25,
6.5V Vin 12V 4.900 5.000 5.100 V Line Regulator GU1086-XXX Io=10mA, Vout+1.5<Vin<12 - - 0.2 % GU1086-ADJ Vin=3.3V, 0mA<Io<1.5A, T J=25 (Note 1,2)- - 1 %
GU1086-1.5 Vin=3.0V, 0mA<Io<1.5A, T J=25 (Note 1,2)- 12 15 mV
GU1086-1.8 Vin=3.3V, 0mA<Io<1.5A, T J =25 (Note 1,2)- 15 18 mV
GU1086-2.5 Vin=4.0V, 0mA<Io<1.5A, T J=25 (Note 1,2)- 20 25 mV
GU1086-3.3 Vin=5.0V, 0mA<Io<1.5A, T J=25 (Note 1,2)- 26 33 mV Load Regulation
GU1086-5.0 Vin=8.0V, 0mA<Io<1.5A, T J=25 (Note 1,2)- 40 50 mV Dropout Voltage
(Vin-Vout) GU1086-XXX Io=1.5A( Vout=1% Vout) - 1.3 1.4 V Current Limit GU1086-XXX Vin-Vout=5V 1.6 - - A Minimum Load Current Adjustable model Vin=5V - 5 10 mA Adjust Pin Current Adjustable model Vin=12V, Io=10mA - 55 100 uA Quiescent Current fixed model Vin=12V, Io=0mA - - 12 mA Thermal Regulation T A=25 , 30ms pulse - 0.008 0.04 %/W
F=120Hz, C OUT=25uF, Tantalum, Io=1.5A伸缩杆
Ripple Rejection
GU1086-XXX Vin=Vout+3V - 60 70 dB Temperature Stability Io=10mA - 0.5 - %
Thermal Resistance Junction–to-Ambient (No heat sink ;No air flow) - 83 - /
W
Thermal Resistance
Junction-to-Case Control Circuitry/Power Transistor - 0.65/2.7 - /
W Note 1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction Temperature by low duty cycle pulse testing. Load regulation is measured at the output lead =1/18” from the package.
Note 2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference in input and output and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
Functional Description
Introduction
The GU1086 adjustable or fixed-mode Low Dropout (LDO) regulator is a 3 terminal device which can easily be programmed by internal mask change to any voltage within the range of 1.25 to Vin-1.4V. T
摄像头
测试he GU1086 only needs 1.4V differential between Vin and Vout to maintain output regulation, in addition, the output voltage tolerances are also extremely tight and they include the transient response as port of the specification. For example, Intel VRE specification calls for a total of ±100mV including initial tolerance, load regulation and 0 to 1.5A load step. The GU1086 is specifically designed to meet the fast current transient needs as well as providing an accurate initial voltage, reducing the overall system cost with the need for fewer output capacitors.
Load Regulation
Since the GU1086 is only a 3 terminal device, it is not possible to provide true remote sensing of the output voltage at the load. But it can supply good load regulation by internal feedback bypass the external loss such as adjustable mode. Stability
The GU1086 requires the use of an output capacitor as part of the frequency compensation in order to make the regulator stable .For most applications a minimum of 10uF aluminum electrolytic capacitor insures both stability and good transient response.
Thermal Design
The GU1086 incorporates an internal shutdown that protects the device when the junction temperature exceeds the maximum allowable junction temperatures. Although this device can operate with junction temperatures in the range of 150 , it is recommended that the selected heat sink be chosen such that during maximum continuous load operation the junction temperature is kept below the temperature.
Layout Consideration
The output capacitors must be located as close to the Vout terminal of the device as possible .It is recommended to use a section of a layer of the PC board as a plane to connect the Vout pin to the output capacitors to prevent any high frequency oscillation that may result due to excessive trace inductance.
Typical Performance Characteristics
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议