交联聚乙烯绝缘阻燃电力电缆

槐木可以做防腐木吗

0.6/1kV 交联聚乙烯绝缘阻燃电力电缆

XLPE Insulated Flame-retardant Power Cable

一、产品标准Standard

本产品按GB12706-91《额定电压35kV及以下铜器芯、铝芯塑料绝缘电力电缆》、GB12666.5-90《电线电缆成束燃烧实验》、IEC60754《取自电缆或光缆的材料燃烧时释放出气体的试验方法》和IEC61034《电缆或光缆在特定条件下燃烧的烟密度测定》标准生产，同时还可根据用户需要按国际电工委员会推荐标准IEC、英国标准、德国标准及美国标准生产。

The product is manufactured according to the standard of GB12796-91 and GB12666.5-90 or IEC、BS、DIN and ICEA upon request. 二、适用范围Application

本产品适用于工频额定电压0.6/1kV及以下配电线路作配送电能之用。

The product is suitable for use in power distribution lines with rated power-frequency voltage up to and including 0.6/1kV.

水管温度传感器

三、使用特性Operating characteristics

· 工频额定电压U0/U为0.6/1kV。

Rated power-frequency voltage U0/U为0.6/1kV.

· 电缆导体的最高允许工作温度为90℃。家庭水景喷泉

Max. permissible continuous operating temperature of conductor :90℃.

· 短路时（最长持续时间不超过5S）电缆导体的最高温度不超过250℃。

Max. Short –circuit temperature of the conductor shall not exceed 250℃.

(5s maximum duration).

· 电缆敷设时环境温度应不低于0℃。

The ambient temperature under installation should not below 0℃.

· 电缆的阻燃性能符合GB12666.5-90标准A级或C级要求。

The flame retardant performance of cable is in according with A or C grade request of GB12666.5-90.

· 低烟无卤电缆的无卤性能符合IEC60754《取自电缆或光缆的材料燃烧时释放出气体的试验方法》电缆燃烧时气体逸出试验。

The low smoke and non halo of cable is in according with IEC60754

成品电缆燃烧时绝缘和护套材料的PH值和电导率符合下表的规定。

When end product burning.PH value and conductivity of insulation and sheath material should suit infra – table regulate.

燃烧气体的腐蚀性 Corrosivity of combustion	单位 Unit	指标 Index
PH 值 PH value	-	≥ 4.3
电导率 Conductivity	μ .s/mm	≤ 10
	水泥电阻器

· 低烟无卤电缆的低烟性能符合IEC61034《电缆或光缆在特定条件燃烧的烟密度测定》电缆燃烧烟密度试验。

The low smoke and non halo of cable is in according with IEC61034内网审计

成品电缆燃烧时的最小透光率不小于30%。

When end product burning,the minimum light transmittance should not less than 30%.

· 电缆弯曲半径不小于电缆外径15倍。

The bending radius of cable should not less than 15 times of the cable diameter.

四、电缆的型号、名称和使用范围 Type Designation &Application of cable.

五、生产范围 Production Range of nCable

*单芯铠装电缆仅用于直流系统，若用于交流系统，应采用非磁性材料铠装或隔磁措施。

*The single core armored cables are used for D.C Systenm only.As for A.C system,the magnetic isolation should be applied on the steel armor wires or non-magnetically materials should be used.

六、电缆结构尺寸及主要技术参数 Construction and Main technical data

0.6/1KV单芯交联聚乙烯绝缘阻燃电力电缆

0.6/1kv Signie Core XLPE Insulated Flame – retardant Power Cable

注：#表示导体为紧压圆形

Where:# = compact circular standed conductor

0.6/1kv两芯交联聚乙烯绝缘阻燃电力电缆

muhdpe合金管

0.6/1kv 2 Cores XLPE Insulated Flame – retardant Power Cable

0.6/1kv两芯交联聚乙烯绝缘钢带铠装阻燃电力电缆

0.6/1kv 2 Cores XLPE Insulated Steel Tape Armoured Flame – retardant Power Cable.

注：#表示导体为紧压圆形;*表示导体为紧压扇形

Where:# = compact circular standed conductor *=compact sector stranded conductor

0.6/1kv两芯交联聚乙烯绝缘钢丝铠装阻燃电力电缆

0.6/1kv 2 Cores XLPE Insulated Steel wire Armoured Flame – retardant Power Cable

0.6/1kv三芯交联聚乙烯绝缘阻燃电力电缆

0.6/1kv 3 Cores XLPE Insulated Flame – retardant Power Cable.

0.6/1kv三芯交联聚乙烯绝缘钢带铠装阻燃电力电缆

0.6/1kv 3Cores XLPE Insulated Steel Tape Armoured Flame – retardant Power Cable.

本文发布于:2024-09-22 13:24:47，感谢您对本站的认可！

本文链接：https://www.17tex.com/tex/3/211560.html

上一篇：电线电缆检验方法指南

下一篇：电缆电流计算公式以及对照表

标签：电缆燃烧标准绝缘铠装电力电缆导体

留言与评论（共有 0 条评论）