Die / Tool= 模具
Prog. Die=progressive die 级进模Ball bearing guide posts and bushings=球形滚珠导柱和轴套
Casting die=铸造模Cage=套Part=钣件Rigidity=强度Die material=制模材料Thin=薄
Tool design=模具设计Strip design=料条设计Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口” Tool design approval=模具设计审核
Tool design modification/revision=模具设计更改
Tool parts design (detail) = 模具钣件设计（详细）Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引 FMC Make=保丽龙制作Construction method=结构方法
modification= 更改
Check & measure=检查& 测试
Machining= 机器加工
Large machining=在大型机器上加工上下模架（铣、车等）
Small machining=在小型机器上加工模块等Lower die trim inserts=下模切刃块
Lower trim inserts retainer=下模切刃块承盘Assemble inserts=组立镶块
Punch stripping plates=冲头压料板
Assembly=组立Trim punch backing plates=切刃冲头背板NC Machining=NC雕刻加工Stripper window inserts=料条窗户镶块
Fitting=研磨组立Spotting=合模Die tryout=试模Cushing stroke=缓冲行程
Dowel pin=定位销Guide lift pin=导引升降销
Assemble gas spring=安装氮气缸Stamp parts=冲钣件
Adjustment=调试Run off parts=冲钣件
Lower trim steels=下刃块Hit parts=冲钣件
Section=冲头断面Lifters=提升器
Trim punch=切刃冲头Coil=卷材
jack screw hole=起重[千斤顶]螺旋孔Guide block=导引块
Die set, lower plate=下模架Guide the coil through the tool=导引卷材Die set, upper plate=上模架layout inspection=全尺寸检验
Die inspection & approval=模具检查和审核Stretch carriers=拉伸运送装置
delivery=发货Punch stripping plates=冲头压料板Rejected=拒收Trim punch backing plates=切刃冲头背板Scrapped=报废Stripper window inserts=料条窗户镶块Rework=返工Heel plates=背托
stop block=停止块Prepare for delivery=准备发货
Hydro form 液压成形Key=键
Shear=剪切For locating retainer blocks=承盘键Sensor=传感器For holding buttons or pilots=冲母座或导销
键
Stretch web=拉伸网For fixed heel or positive stop=镶根键Layout the parts=设计钣件Construction method=结构方法Preceding into the design=继续设计Manual Surface Grinder=手动平面磨床Guide the coil through the tool=导引卷材Spotting red=合模用丹红
Checking aid /checking gage=检具Layout ink=试模用蓝墨水
Jig=夹具Masking tape=黄不透明胶带(遮蔽胶带) Fixture=夹具Pliers=尖嘴钳，老虎钳
Ball bearing guide posts and bushings=
球形滚珠轴套
Cresent wrench=可调扳手
山体滑坡监测系统Guide post=导柱Bushings=导套Pump pipe=泵管
Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”CMM=三次元测量仪Symmetric=对称的
The axis of symmetry=对称轴Technical=技术上的Diagonal=对角线
Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引One two three block=一二三模块Adjustable parallels=可调平行块Stop block=阻止块
Granite Table=花岗岩平台Backing Plate=背板
Plotter= .描绘器, 图形显示器, 绘图器, 坐标自记器, 标图员Shoulder Bolt=肩头螺丝(Stripper bolt)
木薯干
Belt Sander=带磨机Keeper Block=行程块Metal Cutting Band Saw=立式带锯床Corner Guide Block=导块Blanchard Grinder=大型平面磨床Dowel pin=定位销
Joe Blocks=精密量块Set Screw=螺塞
Whirly Gig=筒夹式冲子成形器Jig & fixture =夹具
Chamfer Tools=倒角刀具组Checking fixture=检具
Angle Plate=L形直角座Guide Block=导块
Gage Pins=英寸塞规Plunger=柱塞
Sine Plate (magnetic)=正弦磁台Pierce=冲孔
Flute End Mill=硬质合金钢铣刀Wear Strip=耐磨板 Mill Cutter=波纹粗铣刀（标准型）Mating area=组立的接触面
C’bore/ counter bore=六角沉头铣刀Accommodate=适应
Radius Dresser=砂轮修整器Wiping hard (very shiny)= 过分摩擦闭合
[接触]（闪光）
Boring Head & Boring Bar=搪孔器、搪刀杆Pin=销Increase the die clearance between the form steels=增加成形块间隙
Reamer=绞刀Clearance=间隙
Approval=确认Oil paper=油纸
Impact wrench=气动扳手0-11” Micrometer=0-11”千分尺Air pin=空气销Trim line=切边
bumper
[‘bQmpE(r)] n.缓冲器+/-0.5mm unless otherwise specified
插座保护盖除非另有规定，否则公差为+/-0.5mm
V endor [‘vendE(r), -dC:(r)] n.卖主Part tolerance=钣件公差stripper layout=排样图Ball nose=球刀
drawing of panel #987415&16=钣件设计图（公差）Bore=镗
Line tap=攻丝校直
Arbor =柄轴；心轴Borer=镗刀，镗床
Drill chuck=钻夹头Chamfer=倒角
Button=冲母座Radius=半径
Nitrogen Cylinder=氮气缸Coolant=切削液
Pilot=导销Punch=冲头
Retainer=承盘Distribution Blocks=接头座Button=冲母座Screw=螺丝
Hose Straps=软管夹（塑料）Shop=车间
Flat Feet Keepers=顶料销Crib=仓库
Ejector Pin=顶出销CNC mill= CNC机床
Spring=弹簧Jack=千斤顶
Straight Port Adapter=直管接头Strips=料条
Y-205 Hose=软管（塑料）Styrofoam [`stairEfEum]
n.聚苯乙烯泡沫塑料（保丽龙材料）Short Neck Adapter=短接头Cut off=落料
45。Swivel= 45。接头(adjustable) Idle station=空站（for changeability of the
part in the future）
再生素
45。Elbow=45。接头(un-adjustable) Dry run=空转(to check the interference 干涉of
a die)
Compact Swivel Adapter=转接头Form=成形
Control Panel=控制面板Trim=切边
Stamp Retainer=承盘Perforate= [‘p\:fEreit] v.打孔
Spotting press=合模机Plumber=水管工人[‘’plQmE(r)]
Hand grinder=角磨机Y o-yo 卷尺(美)
Surface grinder=平面磨床Drill chuck=钻头夹
Blanchard grinder=大型平面磨床Tape measure=卷尺
End mill=端铣刀/立端刀Protractor=量角器
Ball nose end mill=球头铣刀Switch=限位开关
Straight edge=直角座Caliper=卡尺
Shim stock=垫片Slug=废料
Oversize tap=加大尺寸丝攻Fittings=接头
Die=模具Crimping machine=氮气缸接头夹具
Upper die=上模Manual surface grinder=手动平面磨床Lower die=下模Push cart=推车
Die set=模架Tool box=工具箱
Button die=冲母座Heel block=镶根
Pilot=导销Tap=攻丝
Bushing=衬套
Feeler gage=塞尺
HRS=hot roll steel =热轧钢卷Belt sander=砂带机
CRS=cold roll steel=冷轧钢卷Metal cutting band saw=带锯（切割金属）Insert=镶块Joe blocks=测量块
Guide post=导柱Scriber=划线器
Crane=吊机Zinc coating=镀锌
Stripper pad=压料板Ball peen hammer=球形榔头
Dowel pin=定位销Rosin=松香水
Heat treat=热处理Wire burn=线割Gage pins= Round cylinders of precise dimension used for measuring holes.
Fast wire burn=快走丝Blank die=下料模
Slow wire burn=慢走丝Tryout material=试模材料
Stripper pad=压料模(Pad retainer) shoulder bolt=stripper bolt=肩
头螺丝（all can be used for guiding a pad）Trim block (steel)=切刃块Pad retainer=压料模承盘
Form block (steel)=成形块Drill chuck=钻夹头
Drill vice=平口夹钳
Pig putty= epoxy Putty=油灰Parallel=平行块/肋条
Sandblast=喷沙器喷沙
(a pressurized air sand mixture) Graphite =石墨（lubricant）[‘grAfait] n.
Plumb=
[plQm] n.铅锤, adj.垂直的
vt.使垂直, 用铅增加重量, 探测vi.垂直Plumber= n. 水管工人[‘plQmE(r)
Solder (lead)=
[‘sE u ldE(r); (?@) ‘s odEr] n.焊料v.焊接(铅条) Titanium nitrate (Tin coating-hard) =[化]硝酸钛(钛化处理)
Binder= ‘ba indE(r)]
n.环模线，装订工, 包扎者, 包扎工具, Adjustable locking pliers (vice grip) =可调锁紧老虎钳
甲酸沸点blind hole=闷眼, 盲孔Steel shavings=铁屑
slip fit=滑(动)配合Cast iron=铸铁
sliding chute=滑槽Threads=螺纹
Ratchet wrench 棘轮扳手Spacer block=间隔体(有时也叫平衡块) Vise grips=大力钳Semi-stripper=半脱件导游扩音器
V argus debur tool=去毛刺器Clamp block=楔子
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议