代码 | 报警内容 | 注解 | 代码 | 报警内容 | 注解 |
2001 | FUSE BLOWN | 熔丝烧断 | 2039 | START CONDITION FAILURE | 开始条件故障 |
2002 | OVERLOAD | 过载 | 2040 | SPINDLE LOAD NG | 主轴负载不正常〔XXXX〕 |
2006 | SLIDING SURFACE LUBRICATION LOW | 滑动面润滑不足 | 2041 | MG POT UP&DOWN SIGNS ON | |
2007 | LUBRICATOR TROUBLED | 润滑器问题，滑动 | 2044 | LUBRICATING UNIT ALARM | 润滑装置报警 |
2010 | ABNORMAL COOLANT LEVEL | 冷却液位异常 | 2045 | TOOL CLAMP & UNCLAP SIGNAL ON | 工具夹紧与松开信号开 |
2011 | COOLANT UNIT TROUBLED | 冷却装置问题 | 2049 | MAINTENANCE REQUEST | 维修请求 |
2014 | WATCH TOOLS GIVING ALARM | “注意刀具”引起的报警 | 2052 | EXTERNAL MULTIPLE APC ALARM | 外部多托盘APC报警 |
2015 | MG AMP UNIT TROUBLED | “刀库放大器装置”问题 | 2054 | PALLET MOVEMENT & MG SETUP DETECTOR | 托盘移动与刀库安装检测器信号开核反应堆的慢化剂 |
2016 | EXTERNAL GIVING ALARM | “外部装置”引起的报警 | 2055 | PALLET MOVEMENT UP & DOWN DETECTOR | 托盘上下移动检测器信号开 |
2017 | MEASURING UNIT ALARM | 测量装置报警 | 2056 | APC CW & CCW SIGNS ON | APC顺时针与逆时针信号开 |
2019 | INVERTER ALARM | 逆变器报警 | 2057 | APC UP & DOWN SIGNALS ON | APC上下信号开 |
2021 | SPINDLE AMP UNIT TROUBLED | 主轴放大器装置问题 | 2058 | PALLET MOVE MG & WT SIGNS ON | 托盘移动刀库与WT信号开 |
2022 | SPINDLE SPEED IS DECREASING | 主轴速度正在降低 | 2059 | SETTING ST UP & DOWN SIGNS ON | 设置ST上下信号开 |
2023 | TO ROTATE SPINDLE TROUBLED | 要旋转主轴时遇到问题 | 2060 | PALLET MG DETECTOR ALARM | 托盘刀库检测器报警 |
2024 | CAN,T ROTATE SPINDLE | 无法旋转主轴 | 2064 | TABLE CLAMP & NOT SIGNS ON | 工作台夹紧与松开信号开 |
2025 | SPINDLE ROTATING INHIBITED | 禁止主轴旋转 | 2065 | MG HOME SIGN IS MISSING | 刀库初始位置信号遗失 |
2026 | ORIENT MOVING IS NOT GOOD | “定位移动”不正常 | 2066 | MG OVERRUN | 刀库溢出 |
2027 | ORIENT END SIGN ERROR | “定位结束信号”错误 | 2070 | +OT(MG TOOL BREAKAGE) | 刀库刀具破损 |
2028 | 毫米波天线WARMING UP INCOMPLETE | 预热未完成 | 2071 | EMERGENCY STOP LS ON | 紧急停止LS开 |
2029 | PLEASE EXCHANGE THE BATTERY | 请跟换电池 | 2072 | EMS RELEASE ON | “紧急解除”开 |
2030 | NC SERVO PROBLEM | NC伺服问题 | 2073 | ILLEGAL S-CODE | S代码无效 |
2031 | CAN,T START CYCLE | 无法开始“循环” | 2075 | 摄像机三脚架CAN’T FIND THE TOOL | 无法到刀具 |
2032 | CAN,T FEED AXIS | 无法进给“轴” | 2076 | TOOL NO.SETTING ERROR | 刀具编号设置错误 |
2033 | CAN,T START ATC | 无法开始“ATC” | 2077 | CAN’T FIND THE SPARE TOOL | 无法到设备刀具 |
2034 | CAN,TMOVE MG | 无法移动“刀库” | 2078 | M32 SETTING ERROR | M32设置错误 |
2036 | ATC MOVING TROUBLED | “ATC移动“问题〔XX〕 | 2080 | MANUAL OPERATING MODE OF MG | 刀具手动操作模式 |
2037 | MG MOVING TROUBL | “刀库移动“问题〔XXXX〕 | 2086 | M61/M62,PALLET SELECED ERROR | M61/M62，托盘选择错误 |
2038 | APC MOVING TROUBLED | “APC”移动问题〔XX〕 | 2087 | PC MAINTENANCE MODE | PC维修模式 |
OKK报警信息一览表 | |||||
代码 | 报警内容 | 注解 | 代码 | 报警内容 | 注解 |
2088 | 工业废渣制砖 PC CALCUATION ERROR | PC计算错误 | 2144 | (SUB)ATC COVER OPEN FAILURE | （副）ATC 门盖打开故障 |
2089 | ATC RETURN | ATC返回 | 2145 | (SUB)TABLE CLAMP | （副）工作台夹紧 |
2091 | PROGRAM NO.SEARCH ERROR | 程序编号搜索错误 | 2146 | (SUB)TABLE UNCLAMP FAILURE | （副）工作台松开故障 |
2092 | APC RERURNING | APC返回 | 2148 | (SUB)MG COVER CLOSE | （副）刀库门盖关闭故障 |
2093 | PARAMETER ERROR | 参数错误 | 2151 | (SUB)GEAR SHIFT FAILURE | （副）齿冷换挡故障 |
2095 | SOFT SCALE 2M ALARM | 软标尺2M报警 | 2153 | (SUB)ZERO RETURN END IS MISSING | （副）原点返回结束遗失 |
2096 | COMTROL PANEL INPUT ERROR | 负压引流球控制面板输入错误 | 2154 | (SUB)OVERRIDE SIGN SI OVER 101% | （副）超驰信号超过101% |
2097 | FIXTURE ALARM | 夹具报警 | 2155 | (SUB)EXTERNAL UNIT TROUBLED | （副）外部装置问题 |
2098 | ATC COUPLING FAILURE | ATC耦合故障 | 2156 | (SUB)M55 SIGN IS ON | （副）M55信号开 |
2101 | (SUB)POT MG SIDE | （副）刀套刀库侧 | 2158 | (SUB)OIL PRESSURE LOW | （副）油压过低 |
2102 | (SUB)PIT SP SIDE | （副）刀套主轴侧 | 2159 | (SUB)ABSOLUTE VALUE DETECTOR | （副）绝对值检测器 |
2107 | (SUB)ATC ARM HOME POSITION | （副）ATC机械臂初始位置 | 2160 | (SUB)NC UNIT | （副）NC装置 |
| 高频高压电源 2109 | (SUB)SPINDLE TOOL CLAMP | （副）主轴刀具夹紧 | 2164 | (SUB)MG | （副）刀库 |
2110 | (SUB)SPINDLE TOOL UNCLAMP | （副）主轴刀具松开 | 2169 | (SUB)OPERATOR DOOR | （副）操作员门 |
2111 | (SUB)MG ONE PITCH INDEXING | （副）刀库单螺距分度 | 2172 | (SUB)SUPPLY GREASE | （副）供给润滑脂 |
2116 | (SUB)ATC ARM POSITON CHECK FAILURE | （副）ATC机械臂位置检查故障 | 2184 | COOLANT COOLER ALARM | 冷却液冷却器报警 |
2127 | (SUB)APC TURN | （副）APC回转 | 2189 | ALARM POWER OFF | 电源关报警 |
2128 | (SUB)PALLET MG HOME SIGN IS MISS | （副）托盘刀库初始位置信号遗失 | 2192 | RESET DURINGT TAPPING | 攻丝期间复位 |
2130 | (SUB)PALLET HOME POSITON | （副）托盘初始位置 | 2194 | COOLANT:SHORTAGE/FILLING SP | 冷却液：短缺、加注主轴 |
2131 | (SUB)APC UP | （副）APC向上 | 2195 | FILTER STOP UP | 滤清器阻塞 |
2132 | (SUB)PALLET MOVE WT SIDE | （副）托盘移动WT侧 | 2197 | OIL-AIR UNIT TROUBLED | 油气装置问题 |
2133 | (SUB)APC DIWN | （副）APC向下 | 2199 | AIR UNIT TROUBLED | 空气装置问题 |
2134 | (SUB)PALLET MOVE MG SIDE | （副）托盘移动刀库侧 | 2200 | MISMSTCH PC PARAMETER | PC参数不匹配 |
2135 | (SUB)PALLET MOVE UP FAILRE | （副）托盘向上移动故障 | 2143 | (SUB)ATC COVER SHUT | （副）ATC 门盖关闭 |
2136 | (SUB)PALLET MOVE DOWN FAILURE | （副）托盘向下移动故障 | 2139 | (SUB)PALLET CONTACT FAILURE | （副）托盘接触故障 |
2137 | (SUB)PALLET CLAMP | （副）托盘夹紧 | 2141 | (SUB)APC COVER CLOSE FAILURE | （副）APC门盖关闭故障 |
2138 | (SUB)PALLET UNCLAMP | （副）托盘松开 | |||
本文发布于:2024-09-22 07:16:09，感谢您对本站的认可！
本文链接：https://www.17tex.com/tex/2/275613.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议