一、Vehicle classification 汽车分类1.1 Car轿车
序号英文中文
1 passenger car轿车
2 minicar微型轿车
3 subcompact car普通级轿车
4 compact car中级轿车
5 intermediate car中高级轿车
6 limousine car高级轿车
1.2 Bus客车
序号英文中文
1 bus客车
2 mini-bus微型客车
3 light bus轻型客车
后桥壳4 medium bus中型客车
5 large bus大型客车
6 extra bus特大型客车
7 articulated bus铰链客车
8 double-deck bus双层客车
1.3 Motor truck 货车
序号英文中文
1 motor truck货车
2 mini- truck微型货车
3 light truck轻型货车
4 medium truck中型货车
5 heavy truck重型货车
6 off-road vehicle越野汽车
1.4 special purpose vehicle专用汽车
序号英文中文
1 special purpose vehicle专用汽车
2 van厢式汽车
3 tanker罐式汽车
4 dump truck自卸汽车
序号英文中文
5 semi-trailer towing vehicle半挂牵引汽车
6 full-trailer toeing vehicle全挂牵引汽车
二、Vehicle construction汽车构造2.1 Main components of vehicle汽车主要组成序号英文中文
2 front axle前桥
3 wheel车轮
4 clutch离合器
5 gearbox变速器
6 propeller shaft传动轴
7 universal joint万向节
8 final drive and differential主减速器和差速器
9 rear axle后桥
10 body车身
2.2 Vehicle performance汽车性能
序号英文中文
1 maximum speed of the automobile汽车最高车速
2 time of acceleration of the automobile汽车加速时间
3 maximum gradability of the automobile汽车最大爬坡度
4 constant-speed fuel econ-omy of the automobile汽车等速油耗
5 economical speed of the automobile汽车经济车速
2.3 engine position发动机布置
序号英文中文
1 front engine , rear wheeldrive前置发动机,后轮驱动
2 rear engine , rear wheeldrive后置发动机,后轮驱动
序号英文中文
3 front engine , front wheeldrive前置发动机,前轮驱动
4 under cab-floor engine驾驶室下置发动机
5 underfloor engine车厢地板下置发动机
三、Vehicle dimensions汽车尺寸
序号英文中文
1 vehicle overall length车长
2 vehicle overall width车宽
3 vehicle overall height车高
4 front overhang前悬
5 real overhang后悬
6 wheelbase轴距
7 tread轮距
8 ground clearance 最小离地间隙
9 angle of incidence接近角
10 descent angle离去角
四、Wheel alignment前轮定位
序号英文中文
1 caster 主销后倾
2 steering axis inclination主销内倾
3 camber 前轮外倾
胶囊模具
4 toe-in前轮前束
五、Diameter of turning circle转弯直径
序号英文中文
1 steering angle 转向角
2 outside diameter of minimum turning circle最小转弯外径
3 minimum turning circlediameter最小转弯直径
4 Inside diameter of minimum turning circle最小转弯内径
5 Turning clearance circle转弯通道圆
第二类 ENGINE发动机
一、Engine construction发动机构造
序号英文中文
1 rocker arm cover摇臂罩
2 valve rocker arm气门摇臂
3 camshaft凸轮轴
4 camshaft drive凸轮轴驱动轮
5 spark plug lead火花塞导线
6 timing belt cover正时皮带罩
7 valve spring气门弹簧
8 poppet valve菌形气门
11 timing belt正时皮带
12 combustion chamber燃烧室
13 cylinder block汽缸体
14 water jacket 水套
15 oil filter机油滤清器
16 flywheel飞轮
17 ring gear齿圈
18 oil gage机油标尺
19 oil pan/sump油底壳
20 crankshaft曲轴
21 drain plug放油孔塞
22 v-belt pulley V型皮带轮
二、Essential term基本术语
序号英文中文
1 cylinder diameter汽缸直径
3 crank radius曲轴半径
4 piston displacement活塞排量
5 compression chamber volume压缩室容积
6 total cylinder volume总汽缸容积
7 top dead center上止点
8 bottom dead center下止点
三、Engine operation principle发动机工作原理
3.1 Four-stroke gasoline engine operation principle四冲程汽油机工作原理序号英文中文
1 intake stroke进气行程
2 compression stroke压缩行程
3 expansion stroke膨胀行程
4 exhaust stroke 排气行程
太阳能光伏密封胶5 combustible mixture可燃混合气
6 intake valve进气门
7 spark plug火花塞
8 exhaust valve排气门
9 exhaust gas废气
3.2 Four-stroke diesel engine operational principle四冲程柴油机工作原理序号英文中文
1 intake stroke进气行程
2 compression stroke压缩行程
3 expansion stroke膨胀行程
4 exhaust stroke 排气行程
5 intake进气
6 compression压缩
7 combustion燃烧
8 expansion膨胀
9 exhaust排气
10 air空气
11 injector喷油器
12 exhaust gas废气
3.3 Two-stroke gasoline engine operation principle二冲程汽油机工作原理序号英文中文
1 combustible mixture可燃混合气
2 inlet port进气口
3 crankcase曲轴箱
4 precompressed mixture预压混合气
序号英文中文
5 transfer canal输气道
6 intake port进气口
7 exhaust port排气口
8 exhaust gas废气
9 spark plug火花塞
3.4 Two-stroke diesel engine operation principle二冲程柴油机工作原理
1 air空气
2 blower pump扫气泵
3 precompressed air预压空气
4 air chamber空气室
5 inlet port 进气口
6 injector喷油器
7 exhaust valve排气门
8 exhaust gas废气
四、Engine performance发动机性能
序号英文中文
1 fixed throttle characteristics速度特性
2 part throttle characteristics 负荷特性
3 engine speed转速
4 torque扭矩
5 horsepower功率
柳条剥皮机6 specific fuel consumption燃油消耗率
五、Crank connecting rod mechanism曲柄连杆机构5.1 Cylinder block机体组序号英文中文
1 cylinder block汽缸体
2 cylinder liner汽缸套
3 cylinder bearing surface汽缸套表面
4 cylinder head汽缸盖
机器人 单片机5 inlet manifold mountingflange进气歧管凸缘
6 oil inlet hole加油孔
7 cylinder head cover汽缸盖罩
序号英文中文
8 cylinder head gasket汽缸盖衬垫
9 oil filter mounting flange机油滤清器凸缘
10 ventilating pipe mounting seat通风管座
11 cylinder block stiffeningrib汽缸体加强肋
半桥驱动器
12 rear main bearing cover后主轴承罩
13 main bearing cap主轴承盖
14 oil sumppan gasket油底壳衬垫
15 oil sump/pan油底壳
16 fuel pump mountingflange燃油泵凸缘
17 ignition distributor mounting flange分电器凸缘
18 camshaft bearing bushseat凸轮轴轴承座
19 camshaft drive(gear)cover凸轮轴驱动齿轮罩
20 cylinder head covergasket汽缸盖罩衬垫
5.2 Piston,connecting rod活塞连杆组
序号英文中文
1 connecting rod shank连杆杆身
2 connecting rod small end连杆小头
3 connecting rod bushing连杆衬套
4 spring clip弹簧卡环
5 piston pin活塞销
6 piston head活塞头部
7 piston ring groove活塞环槽
8 compression ring压缩环
9 oil scraper ring 油环
10 piston skirt活塞裙部
11 piston pin boss活塞销座
12 connecting rod bearing halfshell连杆轴瓦
13 connecting rod cap连杆螺栓