C ycoloy* Resin C1200HF A mericas: COMMERCIAL
PC+ABS, excellent flow/impact/high heat resistance. Low temperature ductility. For automotive, appliance and electrical components.
TYPICAL PROPERTIES¹
TYPICAL VALUE Unit Standard
M ECHANICAL
T ensile Stress, yld, Type I, 50 mm/min
580
k gf/cm²A STM D 638T ensile Strain, yld, Type I, 50 mm/min 5%A STM D 638T ensile Strain, brk, Type I, 50 mm/min 150%
A STM D 638T ensile Modulus, 50 mm/min
23200k gf/cm²A STM D 638F lexural Stress, yld, 1.3 mm/min, 50 mm span 890k gf/cm²A STM D 790F lexural Modulus, 1.3 mm/min, 50 mm span
23900
k gf/cm²A STM D 790
I MPACT
Izod Impact, notched, 23°C
59
c m-kgf/cm A STM D 256 Izo
d Impact, notched, -30°C
49c m-kgf/cm A STM D 256 Instrumented Impact Total Energy, 23°C 553c m-kgf A STM D 3763 Instrumented Impact Total Energy, -30°C
553
c m-kgf A STM D 3763
T HERMAL
H DT, 0.45 MPa, 3.2 mm, unannealed
129
°C A STM D 648H DT, 1.82 MPa, 3.2mm, unannealed 112°C A STM D 648 CTE, -40°C to 40°C, flow
7.2E-051/°C A STM E 831V icat Softening Temp, Rate B/50130°C I SO 306R elative Temp Index, Elec
105°C U L 746B R elative Temp Index, Mech w/impact 80°C U L 746B R elative Temp Index, Mech w/o impact
105
°C U L 746B
P HYSICAL
S pecific Gravity
1.15
-A STM D 792M old Shrinkage, flow, 3.2 mm 0.5 - 0.7%
S ABIC Method Melt Flow Rate, 260°C/5.0 kgf
19
g /10 min A STM D 1238
E LECTRICAL
H ot Wire Ignition {PLC)
3
P LC Code
U L 746A
Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD
CONDITIONS OF SALE, WHICH CAN BE FOUND AT www.sabic-ip.AND ARE AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE
EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN. Each user is responsible for making its own determination as to the suitability of
Seller's products, services or recommendations for the user's particular use through appropriate end-use testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of such product, service or design in a manner that infringes any patent or other intellectual property right. SABIC Innovative Plastics is a trademark of SABIC Holding Europe B.V.* Cycoloy is a trademark of SABIC Innovative Plastics IP BV
(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for selection purposes. Not to be used for part or tool design.
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
C ycoloy* Resin C1200HF A mericas: COMMERCIAL
TYPICAL PROPERTIES¹
TYPICAL VALUE Unit Standard
E LECTRICAL
H igh Ampere Arc Ign, surface {PLC}
1
P LC Code U L 746A C omparative Tracking Index (UL) {PLC}
2
P LC Code U L 746A
F LAME CHARACTERISTICS
U L Recognized, 94HB Flame Class Rating (3)
1.19
m m
U L 94
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD
Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
CONDITIONS OF SALE, WHICH CAN BE FOUND AT www.sabic-ip.AND ARE AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE
EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN. Each user is responsible for making its own determination as to the suitability of
Seller's products, services or recommendations for the user's particular use through appropriate end-use testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible use of any produ
ct, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of such product, service or design in a manner that infringes any patent or other intellectual property right. SABIC Innovative Plastics is a trademark of SABIC Holding Europe B.V.(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for selection purposes. Not to be used for part or tool design.
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
s1200(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutt
ing tools for new molded article.
C ycoloy* Resin C1200HF A mericas: COMMERCIAL
PROCESSING PARAMETERS
TYPICAL VALUE Unit
I njection Molding
D rying Temperature 100 - 110°C D rying Time
3 - 4h rs D rying Time (Cumulative)8h rs M aximum Moisture Content 0.02
%M elt Temperature 275 - 300°C N ozzle Temperature
275 - 300°C F ront - Zone 3 Temperature 260 - 300°C M iddle - Zone 2 Temperature 255 - 295°C R ear - Zone 1 Temperature 250 - 290°C H opper Temperature 60 - 80°C M old Temperature 60 - 90°C B ack Pressure 0.3 - 0.7M Pa S crew Speed
40 - 70r pm S hot to Cylinder Size 30 - 80
%V ent Depth
0.038 - 0.076
m m
Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD
CONDITIONS OF SALE, WHICH CAN BE FOUND AT www.sabic-ip.AND ARE AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE
EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN. Each user is responsible for making its own determination as to the suitability of
Seller's products, services or recommendations for the user's particular use through appropriate end-use testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of such product, service or design in a manner that infringes any patent or other intellectual property right. SABIC Innovative Plastics is a trademark of SABIC Holding Europe B.V.(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for selection purposes. Not to be used for part or tool design.
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议