钣金内孔单词快口预防
1.To avoid debris injury, the open baffle shall be installed in anappropriate position. In the sheet metal processing, there may be long cutting, that is, ribbon cutting, this phenomenon to use the hook to quickly solve, do not directly with hand pull, to avoid affecting the quality of sheet metal processing and operation safety. In order to avoid the sheet metal processing in the broken debris hit people, the need to settle in the appropriate local smooth baffle, strengthen the awareness of safety prevention.
2. When the tool needs to polish the appearance of the workpiece with gauze, move the tool to a safe position, and be careful not to let the hands and clothes contact the appearance of the workpiece. When grinding the inner hole, do not use the gauze, use the stick instead, and the speed should not be too fast.
3. Stop placing things, fixtures, or workpieces on the lathe and the spindle gearbox. Think about your skills at work. Stop fatigue operation, chat operation, multiperson operation, drunk operation, smoking operation.
4. Keep the machine tools, articles and work orderly, and do the handover work well. When cleaning the workplace after work, turn off the power and put all kinds of walking handles in a safe place.
5. When cutting workpieces with irregular shape, balance blocks should be installed, test balancing and then cutting.
6. The tool should be firmly clamped, and the tip of the knife should not exceed 1.5 times the height of the knife body. The shape and size of the gasket under the tool shall be the same as that of the knife body and shall be as small as smooth as possible.
7. In addition to installing active measuring tools on the lathe, stop the tool holder and move the knife holder to a safe position before measuring the workpiece.
8. Ribbon chips and spiral long chips that occur during cutting should be removed with hooks in time, and it is strictly prohibited to pull by hand.
9. Wear good work clothes, wear good cuffs, wear protective glasses, women should wea
r a good work cap, long hair in the hair cap, stop wearing gloves.
10. The chuck must be loaded and unloaded on the spindle of the lathe and conducted after shutdown. The disc can not be removed with the strength of the motor.
11. It is best to use the tray, dial and protruding parts of the workpiece, so as not to hang the clothes and other parts of the body. If there is no shield, keep a distance while operation.
12. When using the top clamping workpiece, pay attention that the center of the top and the center hole of the spindle are completely consistent, and the damaged or crooked top should not be used. Before use, the top and center holes should be cleaned, and the tail seat should be firm at the top.
13. When turning slender workpieces, in order to ensure the operation safety and processing quality, the following knife frame or center frame should be selected, and the processing part beyond the lathe scale should be set up with mobile protective cover and safety marks
翻译：
1.为了避免碎屑伤人，通明挡板应安装在合适的位置。
在进行钣金加工的时候，有可能会出现长切屑，也就是带状的切屑，对这种现象要用钩子赶快的解决，千万不能直接用手拉，避免影响钣金加工质量和操作安全。为了避免钣金加工中崩碎的切屑碰到人，需求在适合的当地安顿通明的挡板，加强安全防备意识。 2.当需要用纱布打磨工件外观时，应将刀具移至安全位置，并注意不要让手和衣服接触工件外观。磨削内孔时，不得用手指支撑纱布，应用木棍代替，同时速度不宜过快。 3.停止将东西、夹具或工件放在车床和主轴变速箱上。工作时要思考会集。停止疲劳操作，聊天操作，多人操作，酒后操作，吸烟操作。
4.保持机床、物品、作业整齐，做好交接工作。下班打扫作业场所时，应关闭电源，将各种走刀手柄放在安全的地方。
5.车削形状不规则的工件时，应安装平衡块，试转平衡后再切割。大功率led电源
水烟炭6.刀具夹紧应牢固，刀头伸出部分不应超过刀体高度的1.5倍。刀具下垫片的形状和尺寸应与刀体的形状和尺寸一致，垫片应尽可能少且平整。
7.除了在车床上安装可以主动测量的量具外，在测量工件之前，应停车并将刀架移动到安全的位置。
8.切削时发生的带状切屑、螺旋状长切屑，应及时用钩子清除，严禁用手拉。
9.工作前穿好工作服，扎好袖口，戴防护眼镜，女工要戴好工作帽，长发放在护发帽内，停止戴手套。
多方会议
10.卡盘必须在车床主轴上装卸，停机后进行，卡盘不能用电机的力气取下。
11.夹紧工件的卡盘、拨盘、鸡心夹的凸出部位最好使用防护罩，以免绞住衣物和身体的其它部位。如果没有防护罩，操作时应注意保持一定距离。
12.使用顶部夹紧工件时，应注意顶部中心与主轴中心孔完全一致，不得使用损坏或歪斜的顶部。使用前，应清洁顶部和中心孔，尾座应顶部牢固。
道口报警器
雅莱减肥饼干
13.车削细长工件时，为了保证操作安全和加工质量，应选择跟刀架或中心架，超过车床规模的加工部分应设置移动防护罩和安全标志
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议