模具英语专业术语上内模：cavity insert 模具述语下内模：core insert
一、入水：gate行位（滑块）：slide
进入位：gate location 镶件：insert
水口形式：gate type 压座/斜鸡：wedge
大水口：edge gate 耐磨板/油板：wedge wear plate
细水口：pin-point gate 压条：plate
水口大小：gate size 撑头: support pillar
转水口：switching runner/gate 唧嘴：sprue bushing
唧嘴口径：sprue diameter挡板：stop plate 二、流道: runner 定位圈：locating ring
热流道：hot runner,hot manifold锁扣：latch 热嘴冷流道: hot sprue/cold runner 扣鸡：parting lock set
唧嘴直流: direct sprue gate推杆：push bar
圆形流道：round(full/half runner 栓打螺丝：S.H.S.B
流道电脑分析：mold flow analysis顶板：eracuretun
流道平衡:runner balance 活动臂：lever arm 热嘴：hot sprue 分流锥：spure sperader
热流道板：hot manifold水口司:bush
发热管：cartridge heater 垃圾钉：stop pin
探针: thermocouples 隔片：buffle
插头：connector plug 弹弓柱：spring rod 插座：connector socket 弹弓:die spring
密封/封料：seal中托司：ejector guide bush 三、运水：water line中托边：ejector guide pin 喉塞：line lpug 镶针：pin
喉管：tube 销子：dowel pin
塑胶管：plastic tube 波子弹弓：ball catch
快速接头：jiffy quick connector plug/socker 喉塞: pipe plug
四、模具零件：mold components 锁模块：lock plate
三板模：3-plate mold斜顶：angle from pin 二板模：2-plate mold斜顶杆：angle ejector rod
边钉/导边：leader pin/guide pin 尼龙拉勾：parting locks
边司/导套：bushing/guide bushing 活动臂：lever arm 中托司：shoulder guide bushing 复位键、提前回杆：early return bar
中托边L：guide pin 气阀：valves
顶针板：ejector retainner plate 斜导边：angle pin
托板：support plate 术语：terms
螺丝：screw 承压平面平衡：parting surface support balance
管钉：dowel pin 模排气：parting line venting 开模槽：ply bar scot 回针碰料位：return pin and cavity interference
内模管位：core/cavity inter-lock模总高超出啤机规格：mold base shut hight
顶针：ejector pin 顶针碰运水：water line interferes withejector pin
司筒：ejector sleeve 料位出上/下模：part from cavith (core) side
司筒针：ejector pin 模胚原身出料位：cavity direct cut on A-plate,core direct cut
推板：stripper plate on B-plate.
缩呵：movable core,return core core puller 不准用镶件：Do not use (core/cavity) insert
扣机（尼龙拉勾）：nylon latch lock用铍铜做镶件：use beryllium copper insert
斜顶：lifter 初步（正式）模图设计：preliinary (final) mold design
模胚（架）：mold base 反呵：reverse core
弹弓压缩量：spring compressed length
稳定性好：good stability,stable
强度不够：insufficient rigidity
均匀冷却：even cooling
扣模：sticking
热膨胀：thero expansion
公差：tolorance
铜公(电极）：copper electrode
工字扣
Mold & die components 模具单元
Mold changing systems 换模系统
Mold core 模芯
Mold heaters/chillers模具加热器
/冷却器
Mold polishing/texturing模具打磨/磨纹Mold repair模具维修GATAL歌词翻译
Molds 模具
Pressing dies 压模
Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具
塑料模具
mould of plastics
注塑模具
injection mould
冲压模具
die
模架
mould base
定模座板
Top clamping plate
Top plate
Fixed clamp plate
水口推板
stripper plate
A板
A plate
B板
B plate
支承板support plate
方铁spacer plate
底针板ejector plate
面针板
ejector retainer plate
回针Return pin
导柱Guide pin
有托导套
Shoulder Guide bush
直导套
Straight Guide bush
动模座板
Bottom clamp plate
Moving clamp plate
基准线
datum line
基准面
datum plan
型芯固定板
core-retainer plate 凸模固定板
punch-retainer plate 顶针
ejector pin
单腔模具
single cavity mould 多腔模具
multi-cavity mould
multi-gating
浇口
gate
缺料
starving
排气
breathing
光泽
gloss
合模力
mould clamping force 锁模力
mould locking force 挤出
extrusion
开裂
crack
循环时间
cycle time
老化
水泥浆比重检测aging
螺杆
screw
麻点
pit
嵌件
insert
活动镶件
movable insert
起垩
chalking
浇注系统
feed system
主流道sprue
分流道
runner
浇口
gate
直浇口
direct gate , sprue gate
轮辐浇口
spoke gate , spider gate
点浇口
pin-point gate
测浇口
edge gate
潜伏浇口
submarine gate , tunnel gate
料穴
cold-slug well
浇口套
sprue bush
流道板
runner plate
排飞槽
vent
分型线（面）parting line
定模
stationary mould，Fixed mould 动模
movable mould, movable half 上模
yig滤波器upper mould，upper half
下模
lower mould，lower half
型腔
cavity
凹模
cavity plate，cavity block
拼块
split
定位销
dowel
定位销孔
dowel hole
型芯
core
斜销
angle pin, finger cam 滑块
slide
滑块导板
slide guide strip
楔紧块
heel block, wedge lock
拉料杆
sprue puller
定位环
locating ring
冷却通
cooling channel
脱模斜度
draft
滑动型芯
slide core
螺纹型芯
threaded core
热流道模具
hot-runner mould
绝热流道模
insulated runner mould
熔合纹
weld line （flow line）
三板式模具
three plate mould
脱模
石膏增强剂ejection
换模腔模具interchangeable cavity mould 脱模剂
release agent
注射能力
shot capacity
注射速率
injection rate
注射压力
injection pressure
差剂
colorant
保压时间
holdup time
闭模时间
closing time
定型装置
sizing system
阴模
female mould，cavity block
阳模
male mould
泥浆固液分离
电加工设备
Electron Discharge Machining 数控加工中心
CNC machine center
万能铁床
Universal milling machine
卧式刨床
Horizontal planer
车床
Engine lathe
平面磨床
Surface grinding machine
去磁机
Demagnetization machine
万能摇臂钻床
Universal radial movable driller 立式钻床
V ertical driller
超声波清洗机
Ultrasonic clearing machine compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具
split mold分割式模具
cavity型控母模
core模心公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板
piston活塞
cylinder汽缸套
chip细碎物
handle mold手持式模具
（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）
two plate两极式（模具）
well type蓄料井
insulated runner绝缘浇道方式
hot runner热浇道
runner plat浇道模块
valve gate阀门浇口
band heater环带状的电热器spindle阀针
spear head刨尖头
slag well冷料井
cold slag冷料渣
air vent排气道
welding line熔合痕
eject pin顶出针
knock pin顶出销
return pin回位销反顶针
sleave套筒
stripper plate脱料板
insert core放置入子
runner stripper plate浇道脱料板guide pin导销
eject rod (bar)（成型机）顶业捧subzero深冷处理
three plate三极式模具
runner system浇道系统
stress crack应力电裂
orientation定向
sprue gate射料浇口，直浇口nozzle射嘴
sprue lock pin料头钩销(拉料杆) slag well冷料井
side gate侧浇口
edge gate侧缘浇口
tab gate搭接浇口
film gate薄膜浇口
flash gate闸门浇口
slit gate缝隙浇口
fan gate扇形浇口
dish gate因盘形浇口
diaphragm gate隔膜浇口
ring gate环形浇口
subarine gate潜入式浇口
tunnel gate隧道式浇口
pin gate针点浇口
Runner less无浇道
(sprue less)无射料管方式
long nozzle延长喷嘴方式
sprue浇口；溶渣
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线upper plate上模板
blanking下料lower plate下模板
stamp letter冲字(料号) die pad下垫板shearing剪断die holder下夹板
tick-mark nearside正面压印die set下模座tick-mark farside反面压印bottom block下垫脚
冲压名称类bottom plate下托板(底板) extension dwg展开图stripping plate内外打(脱料板)
procedure dwg工程图outer stripper外脱料板
die structure dwg模具结构图inner stripper 内脱料板
material材质lower stripper下脱料板material thickness料片厚度零件类
factor系数punch冲头
upward向上insert入块(嵌入件) downward向下deburring punch压毛边冲子press specification冲床规格groove punch压线冲子 die height range适用模高stamped punch字模冲子
die height闭模高度round punch圆冲子burr毛边special shape punch异形冲子
gap间隙bending block折刀
weight重量roller滚轴
total wt.总重量baffle plate挡块
punch wt.上模重量located block定位块
五金零件类supporting block for locationinner guiding post内导柱定位支承块
inner hexagon screw内六角螺钉air cushion plate气垫板
dowel pin固定销air-cushion eject-rod气垫顶杆
coil spring弹簧trimming punch切边冲子lifter pin顶料销stiffening rib punch = stinger 加强筋冲子
eq-height sleeves=spool等高套筒ribbon punch压筋冲子
pin销reel-stretch punch卷圆压平冲子
lifter guide pin浮升导料销guide plate定位板
guide pin导正销sliding block滑块
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板（顶板）
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模) 汪军锋制作***********************
feature die公母模
female die母模(凹模)
豫公网安备41160202000603
站长QQ:729038198
关于我们
投诉建议