实用文案
模具述语 开模槽: ply bar scot
一、入水: gate 内模管位: core/cavity inter-lock
进入位: gate location 顶针: ejector pin
水口形式: gate type 司筒: ejector sleeve 大水口: edge gate 司筒针: ejector pin
细水口: pin-point gate 推板: stripper plate
水口大小: gate size 缩呵: movable core,return core core
puller
转水口: switching runner/gate
扣机(尼龙拉勾): nylon latch lock
唧嘴口径: sprue diameter
斜顶: lifter
二、流道 : runner
模胚(架): mold base
热流道: hot runner,hot manifold
上内模: cavity insert帐篷门
热嘴冷流道 : hot sprue/cold runner
下内模: core insert
唧嘴直流 : direct sprue gate
行位(滑块): slide
圆形流道: round(full/half runner
镶件: insert
流道电脑分析: mold flow analysis
压座/斜鸡: wedge
流道平衡 :runner balance
耐磨板 /油板: wedge wear plate
热嘴: hot sprue
压条: plate
热流道板: hot manifold
撑头: support pillar
发热管: cartridge heater
唧嘴: sprue bushing
探针: thermocouples
挡板: stop plate
插头: connector plug
定位圈: locating ring
插座: connector socket
锁扣: latch
密封/封料: seal
扣鸡: parting lock set
三、运水: water line
推杆: push bar
喉塞: line lpug
栓打螺丝: S.H.S.B
喉管: tube
顶板: eracuretun
塑胶管: plastic tube
活动臂: lever arm
快速接头: jiffy quick connector
分流锥: spure sperader
plug/socker
四、模具零件: mold components 水口司 :bush
三板模: 3-plate mold 垃圾钉: stop pin
二板模: 2-plate mold 隔片: buffle
边钉/导边: leader pin/guide pin 弹弓柱: spring rod
边司/导套:步进梁式加热炉 bushing/guide bushing 弹弓:die spring
中托司: shoulder guide bushing 中托司: ejector guide bush
中托边 L:guide pin 中托边: ejector guide pin
顶针板: ejector retainner plate 镶针: pin
托板: support plate 销子: dowel pin
螺丝: screw bbzs波子弹弓: ball catch
管钉: dowel pin 喉塞: pipe plug
文案大全
实用文案
锁模块: lock plate Mold repair 智能对话娃娃模具维修
斜顶: angle from pin Molds 模具
斜顶杆: angle ejector rod Pressing dies 压模
尼龙拉勾: parting locks Quick die change systems 速换模系统
活动臂: lever arm Quick mold change systems 快速换模系统
复位键、提前回杆: early return bar
三、模具
气阀: valves 塑料模具 mould of plastics
斜导边: angle pin 注塑模具 injection mould
术语: terms 冲压模具 die 承压平面平衡: parting surface support 模架 mould base
balance
定模座板 Top clamping plate
模排气: parting line venting
Top plate
Fixed clamp plate
回针碰料位: return pin and cavity
水口推板 stripper plate interference
模总高超出啤机规格: mold base shut A 板 A plate
hight
B 板 B plate
顶针碰运水: water line interferes 支承板 support plate withejector pin 方铁 spacer plate 料位出上 /下模: part from cavith (core) 底针板 ejector plate side |
|
模胚原身出料位: cavity direct cut on A- 面针板 ejector retainer plate
plate,core direct cut on B-plate. | | 回针 Return pin |
| | |
导柱 Guide pin
不准用镶件: Do not use (core/cavity)
有托导套 Shoulder Guide bush insert
用铍铜做镶件: use beryllium copper 直导套 Straight Guide bush
insert
动模座板 Bottom clamp plate
初步(正式)模图设计: preliinary (final)
Moving clamp plate
mold design
基准线 datum line
反呵: reverse core
基准面 datum plan
弹弓压缩量: spring compressed length
型芯固定板 core-retainer plate
稳定性好: good stability,stable
凸模固定板 punch-retainer plate
强度不够: insufficient rigidity
顶针 ejector pin
均匀冷却: even cooling
单腔模具 single cavity mould
扣模: sticking
多腔模具 multi-cavity mould
热膨胀: thero expansion
多浇口 multi-gating
公差: tolorance
浇口 gate
铜公(电极): copper electrode
缺料 starving
Mold & die components 模具单元
排气 breathing
Mold changing systems 换模系统
光泽 gloss
Mold core 模芯
合模力 mould clamping force
Mold heaters/chillers 模具加热器 /冷却器
锁模力 mould locking force
Mold polishing/texturing 模具打磨 /磨纹
挤出 extrusion
文案大全
实用文案
开裂 crack 滑动型芯 slide core 循环时间 cycle time 螺纹型芯 threaded core 老化 aging 热流道模具 hot-runner mould
螺杆 screw 绝热流道模 insulated runner mould
麻点 pit 熔合纹 weld line (flow line )
嵌件 insert 三板式模具 three plate mould
活动镶件 movable insert 脱模 ejection
起垩 chalking 换模腔模具 interchangeable cavity mould
浇注系统 feed system 脱模剂 release agent
主流道 sprue 注射能力 shot capacity 分流道 runner 注射速率 injection rate
浇口 gate 注射压力 injection pressure
直浇口 direct gate , sprue gate 差剂 colorant 轮辐浇口 spoke gate , spider gate 保压时间 holdup time
点浇口 pin-point gate 闭模时间 closing time
测浇口 edge gate 定型装置 sizing system
潜伏浇口 submarine gate , tunnel gate 阴模 female mould ,cavity block
料穴 cold-slug well 阳模 male mould
浇口套 sprue bush 电加工设备柿子去皮机 Electron Discharge Machining
流道板 runner plate 数控加工中心 CNC machine center
排飞槽 vent 万能铁床餐台滑轨 Universal milling machine
分型线(面) parting line 卧式刨床 Horizontal planer